Ankara University
Discipline

Fizik Mühendisliği Anabilim Dalı

Ankara University

97

Archived Theses

0

DOIs Assigned

0%

DOI Rate

Discipline

50 Theses
Master'sOpen AccessTR

Pikrik asit ile 2-aminofenol ve 4-aminofenol arasında oluşan enerjik ko-kristallerin x-ışını kırınımı ve kuantum mekaniksel hesaplama yöntemleri ile incelenmesi

Bu tezin temel amacı, patlayıcı olarak yaygın kullanıma sahip pikrik asit (TNP,2,4,6-trinitrofenol) [C6H2 (NO2)3OH] ile 2-aminofenol ve 4-aminofenol [C6H4NH3OH] arasında proton transferi yoluyla oluşan enerjik ko-kristallerin deneysel ve kuantum mekaniksel yöntemlerle incelenmesidir. Tezde incelenen, pikrik asit ve aminofenol bileşenli ko-kristaller bu çalışma kapsamında Ankara Üniversitesi Fen Fakültesi Kimya Bölümü öğretim üyesi Prof. Dr. Orhan ATAKOL tarafından ilk kez sentezlenmiş ve x-ışını tek kristal kırınım (XRD) yöntemi ile kristal ve moleküler yapıları deneysel olarak belirlenmiştir. Tez kapsamında konunun kolay takip edilebilmesi için, pikrik asit (PA) ile 2-aminofenol (2A) ve 4-aminofenol (4A) arasında oluşan ko-kristal (KK) isimleri kısaltılarak sırasıyla, PA-2A-KK ve PA-4A-KK olarak kullanılmıştır. PA-2A-KK kristalinin molekül formülü [C6H2(NO2)3O.C6H4NH3OH] olup, triklinik kristal sisteminde, P-1 uzay grubunda ve a = 8,1456(12) Å, b = 8,4827(12) Å, c = 10,3466(14) Å, alfa = 79,745(4)°, beta = 82,017(4)°, gama = 88,870(4)° birim hücre parametrelerine sahip olduğu belirlenmiştir. PA-4A-KK kristalinin molekül formülü [C6H2(NO2)3O.C6H4NH3OH.H2O] olup, yapıya bir mol su girdiği görülmektedir. Yapı, monoklinik kristal sisteminde, P21/c uzay grubunda ve birim hücre parametrelerinin a = 14,998(2) Å, b = 7,7882(12) Å, c = 13,1987(19) Å ve beta = 109,481(5)° olduğu belirlenmiştir. PA-4A-KK'nın yapısına girmiş olan su molekülünün PA ile 4A arasında oluşan ko-kristal yapının oluşmasına ve kararlılığına katkı sağladığı belirlenmiştir. PA-2A-KK ve PA-4A-KK ko-kristallerin gaz fazı için kuantum mekaniksel hesaplamalar yapılmıştır. PA ile 2A ve 4A molekülleri ko-kristal oluşturmadan serbest molekül olarak birbirine yakın yerleştirilerek elde edilen yapıların da kuantum mekaniksel hesaplamaları yapılmıştır. PA ile 2A ve PA ile 4A'nın serbest molekül (SM) durumuna karşı gelen molekül isimleri sırasıyla PA-2A-SM ve PA-4A-SM olarak kısaltmasıyla kullanılacaktır. Bu moleküllerin gaz fazı için kuantum mekaniksel hesaplamalar yapılmasının amacı, tek kristal olarak sentezi gerçekleştirilememiş olan bazı patlayıcıların özelliklerinin hesaplamalı yöntemlerle araştırılarak, yapı hakkında elde deneysel sonuçlarla ne oranda yakın bilgiye ulaşılabileceği test edilmesidir. Buradan yola çıkarak, deneysel çalışma imkânı bulunamayan bazı yapılar ile ilgili birtakım fiziksel ve kimyasal bilgilere kuramsal hesaplamalar ile ulaşmaya çalışmaktır. Bu tez önerisinde çalışma konusu olarak, PA ve TNT moleküllerinin 4A ile ko-kristallerinin sentezlenmesi ve deneysel olarak ve kuantum mekaniksel yöntemlerle incelenmesi yer almaktaydı. Ancak, TNT ile 4A kullanılarak bir ko-kristal sentezi gerçekleştirilemediği için bu çalışmanın devamı niteliğinde, TNT ile 4A ve TNT ile 2A serbest moleküllerinin kuramsal çalışması yapılacak, tezde elde edilen deneysel ve kuramsal sonuçların benzerliğinden faydalanarak da TNT-2A-SM ve TNT-4A-SM yapıları hakkında bilgiye elde edilmeye çalışılacaktır. Kuramsal hesaplamalarda, Hartree-Fock (HF) ve Møller-Plesset ikinci dereceden pertürbasyon teorisi (MP2) ve yoğunluk fonksiyoneli teorisi (YFT) yaygın adıyla Density Functional Theroy (DFT) metotları kullanılmıştır. Başlangıçta HF, MP2 ve DFT/B3LYP metotlarının her biri için 3-21G, 6-31G(d,p), 6-311G(d,p) baz setleri kullanılarak, PA-2A-KK ve PA-4A-KK ko-kristal moleküllerin doğrudan tek nokta enerji (Single Point Energy SPE) değerleri ve PA-2A-SM ve PA-4A-SM serbest moleküllerin optimizasyonu sonucu tek nokta enerji değerleri hesaplanmıştır. Elde edilen sonuçlardan yola çıkarak, tezde incelenen yapılar için en uygun metot ve baz setinin DFT/B3LYP/6-311G(d,p) olduğu belirlenmiştir. Bu metot ve baz seti kullanılarak, PA-2A-KK ve PA-4A-KK ko-kristal moleküllerin ve PA-2A-SM ve PA-4A-SM serbest moleküllerin gaz fazı için moleküler sınır orbitaller (HOMO, LUMO) ve bağlanma enerjileri hesaplanmıştır, potansiyel enerji yüzeyleri (PSE) çizilmiştir. PA-2A-KK ve PA-4A-KK ko-kristallerin katı fazı için, XRD verilerinden elde edilen CIF dosyası kullanılarak, Hirshfeld yüzey analizi yapılmış ve parmak izi grafikleri elde edilmiştir. Yapıların kimyasal sertlik, kimyasal yumuşaklık, kimyasal potansiyel, elektrofilik indeks, elektronegatiflik ve oksijen dengesi değerleri hesaplanmıştır. Yapıların reaktiflik parametreleri karşılaştırılarak hangi yapının daha kararlı olduğu belirlenmiştir. Kuantum mekaniksel hesaplamalar için girdilerin oluşturulması ve sonuçlarının analizinde GaussView 5.0.9 programı, hesaplamaların gerçekleştirilmesi için Gaussian 09 programı kullanılmıştır. CrystalExplorer21 programı kullanılarak ko-kristal yapıların Hirshfeld yüzey analizi yapılmıştır.

Levent Türker
Hacettepe University · Institute of Graduate Studies in Science
2024
00
Master'sOpen AccessTR

Tam fiber optik akustik vektör algılayıcı sistemlerinin simülasyonu ve sistemlerin hassasiyet analizi

Akustik vektör algılama için geliştirilen tam fiber optik algılayıcı sistemler yüksek hassasiyet, küçük hacimsel yük, düşük maliyet ve elektromanyetik girişimlerden etkilenmemesi sebebiyle akustik dalga ölçümlerinde kullanılmaktadır. Fiber optik tabanlı akustik sistemler, limanlarda su altı güvenliğinin sağlanmasından, denizaltı yan dizin sonarlarına, deniz dibi doğal gaz aramasına, balık tespit edilmesine kadar pek çok alanda mevcut yöntemlere alternatif oluşturmaktadır. Fiber optik tabanlı akustik algılayıcı tasarımlarında Fiber Bragg Izgarası (Fiber Bragg Grating, FBG) teknolojisi ile mandrel tabanlı girişim sistemleri üzerine çalışmalar yürütülmektedir. FBG yapısının küçük ebatlarda uygulanabilirliği nedeniyle, mevcut ticari ürünlerin yanında, literatürdeki yüksek hassasiyetli algılayıcı tasarımları ile de yarışabilmesi yönünden umut vericidir. Bu tez kapsamında FBG tabanlı optik algılama yöntemi ile ataletsel ivme ölçer tasarımı yapılmıştır. Merkezi dalga boyundaki kaymaya göre, sistemin simülasyonu yapılmış ve analiz sonuçları gerçek değerler ile karşılaştırılmıştır. Simülasyon çalışmaları, alüminyum alaşımı ve poli laktik asit (PLA) malzemeleriyle tamamlanmış; kolay üretilebilirliği nedeniyle PLA ile düşük frekanslarda çalışabilen bir sensör üretilmiştir. Bunun yanında, PLA ile üretilmiş ataletsel vektör sensörün, akustik sinyalin geliş yönüne verdiği tepki incelenmiştir. Farklı geometrik parametre setlerine göre simülasyon çalışmaları yapılmış ve elde edilen sonuçlar, ölçüm sonuçları ile karşılaştırılmıştır.

Bilge Karataş Soranlar
Hacettepe University · Institute of Graduate Studies in Science
2023
00
Master'sOpen AccessTR

Amiloid Aß yapılarının moleküler dinamik simülasyonları

Amiloid-β izoformlarından olan Aβ40 ve Aβ42 fibrillerinin varlığı ve birbirleri ile etkileşimleri Alzheimer hastalığının patolojik özelliklerin biridir. Birçok klinik vaka çalışmasında, SARS-COV-2 virüsü Alzheimer hastalığının seyrini kötüleştirdiği ve ölüm oranlarının artmasına neden olduğu rapor edilmiştir. Araştırmamızın odak noktası, SARS-COV-2 virüsünün amiloidojenik Ser55PheTyrValTyrSerArgValLys63 (SK9) peptiti varlığında Aβ40 ve Aβ42 proteinlerinin 1:1 oranda çapraz tohumlanmasıyla elde edilen heterojen (Aβ40/Aβ42) ve homojen (Aβ40) fibril modellerinin kararlıklarının nasıl etkilendiğini incelemek olmuştur. Gerçekleştirdiğimiz simülasyonlar neticesinde, SARS-COV-2 virüsü varlığı altında heterojen fibril modelinin ile homojen fibril modeline kararlılıkları arasında anlamlı sayılabilecek farklılıklar gözlemlenmemiştir. Ancak, heterojen fibril modelinin merkezi hidrofobik bölgesinin karboksil ucu hidrofobik bölgesinin rezidüleriyle homojen fibril modeline göre daha fazla etkileşim içinde olduğu görülmüştür (yayınlanmamış veri).

Recep Keskin
Hacettepe University · Institute of Graduate Studies in Science
2023
00
Master'sOpen AccessTR

Polimer mikrokirleticilerin su ortamında 3B nanoskopik karakterizasyonları ve yapay kirlenmiş suların farklı benzetim teknikleri ile tasarımı

Mikro ve nanoplastiklerin doğal su kaynaklarını kirlettikleri artık bilinen bir gerçektir. Halk sağlığını tehdit eden ve acil olarak önlenmesi gereken bir sorunun çözümü için alternatif bilimsel yaklaşımlar çeşitli projeler ile değerlendirilmekte, geliştirilmekte ve günlük hayata geçirilmektedir. "Nanoplastiklerin Mineralizasyonu için GO-TiO2-Fe3O4 ile Sepiyolit-WO3- Fe3O4 Nanokompozitleri ile Fotokatalitik Ozonlama (FO) Arıtma Veriminin, Nanokompozit Geri Kazanım ve Tekrar Kullanımının Değerlendirilmesi" başlıklı, TÜBİTAK projesi (ÇAYDAG 121Y201) kapsamında yapılan analizlerin bir kısmı bu yüksek lisans tez çalışması ile gerçekleştirilmiştir. Öncelikle mevcut kirli sularda yaygın bulunan kirletici plastiklerin nanoskopik karakterizasyonları yapılarak su ortamındaki morfolojileri, boyut ve dağılımları takip edilebilmiştir. Bu işlemler için kirli ve temiz su örneklerinin yanında, kirletici polimer malzemeler olarak, Polistiren (PS), Naylon66, Polivinil Klorür (PVC), Poliüretan (PU), Polietilen Tereftalat (PET) ve Polipropilen (PP) kullanılmıştır. Antalya- Manavgat Çavuşköy Mevkii deniz kıyısından toplanan plastik atıkların yapıları belirlenerek bu plastik malzemelerin kirletici olmadan önceki yapılarına göre farklılıkları, moleküler düzeyde FTIR ve WAXS analizleri ile, nanoskopik ölçekte ise, SAXS analizleri ile incelenmiştir. Büyük plastik kalıntıların parçalanmasıyla oluşan nanoplastikler (NP' ler) (<100 nm) tez çalışmasının odağında bulunmaktadır. Fiziko-kimyasal etkilerle kolay bozunmayan, canlıların hücrelerine kadar difüz edebilecek küçük boyutlarda olan ve sağlıklı yaşamı doğrudan tehdit eden bu malzemeler bu tez çalışması ile karakterize edilmiş ve sulu ortamlarda nanoskopik yapılarının takip edilebilmeleri mümkün kılınmıştır. Elde edilen bulgulara göre, PP, PVC, Nylon66, PS ve PET malzemelerin parçalanarak, sulu ortamlarda, 10,4 - 20,1 nm yarıçaplı NP' ler halinde yaygın olarak bulundukları tespit edilmiştir. Aynı şekilde bu polimer malzemelerin maksimum parçacık genişlikleri 300 – 550 nm aralığında değişkenlik göstermiştir. PP, PVC, Nylon66, PET malzemelerinde küçülme gözlenirken, PS, PU malzemesinin jirasyon yarıçapında ise büyüme kaydedilmiştir. Çoğu polimer malzemelerin nano morfolojileri fraktal modele uygun bulunmuştur. Yaşlanma sürecinde yine çoğunda morfoloji değişimi gözlenmekle birlikte, sadece PVC yaşlanmasında kararlı yapı korunmuş, yine fraktal morfoloji tespit edilmiştir. Bu da PVC malzemenin kirlilik incelemelerinde ne kadar kararlı yapıya sahip olduğunu göstermektedir. Su arıtma tesisine giren ve çıkan sularda nanoskopik analizler yapıldığında, karakterize edilen NP morfolojileri ile izler sürülmüş ve arıtılmış su ortamında bile nanoskopik PVC bulgularına rastlanmıştır. Arıtılmış su içerisinde tespit edilen PVC polimer malzemesinin etkin yarı çapı 13,2 nm, maksimum çapları ise 450 nm olarak belirlenmiştir. Bu ölçümler sonucunda, su boruları yapımında (malzeme olarak) PVC kullanımının da nano ölçekte su kirliliğine yol açabildiği gösterilmiştir. Yapay olarak yaşlandırmanın etkisini incelemek amacıyla, fabrika üretimi çıkışlı PU malzemesi doğrudan, 8 gün süreyle UV etkisi altında bekletilmiştir. Bununla beraber, yaşlanma süresi tayin edilemeyen, doğadan alınan PU polimer malzemesi de ayrıca incelenmiştir. Doğada bulunan ve yapay olarak sonradan yaşlandırılan PU polimer malzemelerinin örneklemeleri, doğrudan UV radyasyon ile etkileşen ve iç bölümlerinde ışının ilerlediği bölümlerden alınan malzemeler ile yapılmıştır. Bu farklı (dış yüzey ve iç bölüme ait) ikişer örneklemeler incelendiğinde yaşlanmayla beraber (sonradan) yapay yaşlandırılan PU polimerinin nano parçacık yarıçapı 15 nm' den 16 nm' ye yükselirken, doğadan doğrudan alınan yaşlanmış PU polimer malzemesinin yarı çapındaki değişimin çok daha fazla olduğu (17 nm' den 23,6 nm' ye yükseldiği) belirlenmiştir. Böylece UV etkisi ile doğal yaşlanma sürecinde nano partikül boyutlarının arttığı sonucuna ulaşılmıştır. Moleküler ölçekte ise, yapılan FT-IR analizleri ile, her bir malzeme üzerinde doğal fiziko-kimyasal yaşlanma etkileri, atomik ve moleküler bileşenler dikkate alınarak ayrıntısı ile incelenmiştir. Bu analizlerden elde edilen bulgulara göre, doğada yaşlanmanın en fazla etkisi (moleküler yapıdaki değişim olarak) PVC' de ortaya çıkarken, en az yaşlanma etkisi moleküler ölçekte Naylon66 da belirlenmiştir. PU malzemenin yaşlanma sürecinde ise en belirgin moleküler değişim 2800-3000 cm-1 aralığında (C-H bağının simetrik ve simetrik olmayan gerilmesindeki değişim ile) ortaya çıkmıştır. Sonuçta; moleküler ve nanoskopik ölçekte kirletici polimerlerin karakterizasyonları yapılmış, sulu ortamlarda takip edilebilmeleri sağlanmış, doğal koşullarda yaşlanma etkileri incelenmiş, sulu ortamlarda polimer kirletici ile yapay kirlenmiş nano çözeltiler tasarlanmış ve doğal kirlenmiş sularda bulunan polimer nanopartikül teşhisi yapılabilmiştir. Anahtar Kelimeler: Nanoplastikler, Mikrokirleticiler, Nanoskopik Analizler, SAXS, WAXS, FT-IR

Onurcan Bülbül
Hacettepe University · Institute of Graduate Studies in Science
2023
00
Master'sOpen AccessEN

Classification of the glaserite structures family by means of group theory

In this thesis, an extensive analysis of the evaluation of group-subgroup relations of glaserite-type compounds by means of group theory phase transition constraints is aimed. Relations of more than 100 structures were used to create a diagram tree containing the information of structures, index, transformation matrix, lattice distortion and global distortion, as well as possible theoretical structures evaluated in order to find intermediate glaserite-type compounds between the high and low symmetry structures. Glaserite-type compounds are compared among the most related structures according to their cation occupancies of their general chemical formula. Comparison of the crystals was obtained in accordance with their symmetry information via Bilbao Crystallographic Server online tools. In addition, the case study was demonstrated step by step to calculate and analyze the group-subgroup relations of BaNa(PO4)2 crystal via transformation of P-3m1 (#164) minimal supergroup to C2/m (#12) maximal subgroup.

Serpil Albay
Hacettepe University · Institute of Graduate Studies in Science
2019
00
DoctorateOpen AccessTR

Mikro ve nano yapılı süper çözünürlük kırınım optiklerinin tasarımı ve üretimi

Geleneksel optik bileşenlerin çözünürlük sınırının aşılması amacıyla süper çözünürlük optikleri geliştirilmiştir. Bir süper çözünürlük uygulaması olarak mikro kırınım optikleri, ışığın kırılması ilkesi ile çalışan geleneksel optik bileşenlerin çözünürlük sınırının aşılmasında önemli bir yere sahiptir. Foton elekleri, mikro kırınım ilkesiyle çalışan bir optik bileşen tasarımıdır. Bu tezde foton eleklerinin tasarlanması ve mikro fabrikasyon yöntemi olan fotolitografi tekniği ile üretilmesi amaçlanmıştır. Bu kapsamda yapılan çalışmalar iki ana başlık altında toplanmaktadır. Birinci aşamada, süper çözünürlük özelliği gösteren kırınım optiklerinin tasarlanması ve tasarım sonucunda elde edilecek odaklama özelliklerinin araştırılması amacıyla bir simülasyon kodu geliştirilmiştir. Bu kod yardımıyla foton eleklerinin optik performansını belirleyen şiddet dağılımı ve çözünürlük özellikleri üzerinde araştırmalar yapılmıştır. Kullanım alanlarına göre, üç farklı foton eleği modeli tasarlanmış ve özellikleri incelenmiştir. Çözünürlük ve şiddet modülasyonun uygulama alanına göre değiştirebilen model sonuçları, referans foton eleği modelleri ile karşılaştırılmıştır. Buna göre, en yüksek çözünürlüğe sahip modelde, çözünürlükte % 10,5'lik bir artışa karşılık şiddette kayda değer bir düşüş gözlenmemiştir. Elde edilen diğer bir önemli sonuç ise, geliştirilen Tüm Değişken Boyutlu Foton Eleği çözünürlüğün % 2,7 artışı yanında şiddet seviyesinin % 57 artmış olmasıdır. Hem değişen d/w oranı bölgeleri hem de sabit delik çaplarına sahip hibrit bir tasarım için yürütülen üçüncü model, Parçalı Değişken Boyutlu Foton Eleği, simülasyonlarında ise, çözünürlüğün referans foton eleğine göre % 3,6 arttığı belirlenmiştir. Tez kapsamında yapılan çalışmaların ikinci aşamasında, bir mikro fabrikasyon tekniği olan fotolitografi yöntemi ile, özel olarak düşürme ve ıslak kimyasal aşındırma alt yöntemleri ile foton eleklerinin üretilmesi gerçekleştirilmiştir. Çapları yaklaşık 15 - 150 µm arasında değişen iğne delikleri kullanılarak tasarlanan foton elekleri üretilmiştir. Üretim sürecinde fotolitografi tekniğinin özel bir uygulama aracı olan maskesiz lazer yazıcı kullanılmıştır. Her iki alt üretim yöntemi de foton eleği üretimi için optimize edilmiş, elde edilen sonuçlar yorumlanmıştır. Üretimde oluşan hata mekanizmaları analiz edilmiş ve giderilmiştir.

Kemal Rüzgar
Hacettepe University · Institute of Graduate Studies in Science
2019
00
Master'sOpen AccessEN

Surface morphology of randomly disordered liquid crystal

I have studied the quenched random disorder effects created by aerosil dispersion in an octylcyanobiphenyl liquid crystal using atomic force microscopy technique. Liquid crystals have a rich phase variety. The nematic to the smectic-A phase transition in which smectic layers are formed in one dimension while the material is still in a liquid-like condition in two dimensions within the layers is one of the common examples of LC phase transitions. Gelation process in the 8CB+aerosil gels yields a quenched random disorder network which also changes the surface topography. By increasing the aerosil concentration, the original smooth pattern of liquid crystals sample surfaces is suppressed by creating fractal aerosil surface effects; these surfaces become more porous, rougher with more rounded crevices. The dispersed aerosil also serves as pinning centers for the liquid crystal molecules. It has been observed that via the diffusion-limited-aggregation process, aerosil nano-particles yield a fractal-like surface pattern for the less disordered samples. As the aerosil dispersion increases, the surface can be described by more aggregated regions which also introduce more roughness. The results of these analyses, we showed a net correlation between the short-ranged X-Ray peak widths and the calculated surface roughness of the samples. In other words, here we have shown that these quenched random effect gels can also be characterized by their surface roughness.

Rümeysa Salcı
İstanbul Technical University · Institute of Graduate Studies in Science
2018
00
Master'sOpen AccessEN

The compact muon solenoid hadronic forward calorimeter photomultiplier tube tests during the first long shutdown

CERN, the European Organization for Nuclear Research, is an international scientific collaboration founded at 1954 near Geneva. The machines at CERN are particle accelerators and detectors. CERN complex accelerator includes many experiments apart from the LHC experiment. The LHC experiment analyses the particles at the collisions by using its detectors. They are namely ALICE, ATLAS, CMS and LHCb. ATLAS and CMS are general-purpose detectors. ALICE searchs for the structure of quark-gluon plasma which is a phase of matter just after the Big Bang. LHCb investigates the difference between matter and antimatter by using b quarks. The CMS detector is as a cylindrical shape detector and consists of ECAL, HCAL, Muon Stations and Tracking subdetectors. The CMS detector has many physical research programme from Standart Model to extra dimensions and dark matter. The HCAL analyses hadrons and also indirectly uncharged particles, neutrinos. In addition to these goals of the HCAL with ECAL, it searchs for electron/photon, muon and tau identities. The HCAL consists of four sections, barrels ones, HO and HB, endcap HE, and forward HF. The HCAL has two hadronic forward calorimeters, namely HF+ and HF-, the either side of the CMS detector. The HF was made of iron absorber as a passive medium and quartz fiber optics cable as an active medium. Totally, it consists of 36 wedges. Each wedge has two readout boxes and each readout box has 24 PMTs. Totaly, the HF calorimeter has 1728 PMTs. Before the phase 1 of LS1, photomultiplier tubes constructed on the HF are Hamamatsu R7525 PMTs. The purpose of these new Hamamatsu R7600U-M4-200 PMTs with four anodes changing with the old PMTs is to reduce the rate of the anomalous signals from background events. In order to bear this faulty, these new PMTs with higher gain, quantum efficiency and thinner window were chosen to replace with the old PMTs assembled on the HF calorimeter. Also, PMT's baseboard were tested at this station. During phase 1 of LS1, these new PMTs were tested in the PMT and baseboard test station at B904 building at CERN. There are two darkboxes instead of roboxes constructed on the HF calorimeter. Each darkbox has 24 PMTs. At the station, the primary goal is to sort the new PMTs as low, middle and high gain to be assembled on the HF calorimeter. These tests were perfomed by using the blue light emitting diode. This light was used in two types as LED and SPE having different intensities from each other. Some characteristic properties of these new PMTs were analyzed with statistical calculations with respect to PMT test data taken at LED and SPE intensity at the station.

High energy physics
Ersel Bedri Erkurt
İstanbul Technical University · Institute of Graduate Studies in Science
2018
00
Master'sOpen AccessEN

Simultaneous scanning tunneling/atomic force microscopy investigation of diamond surfaces in ultra high vacuum

Diamond has always been one of the most outstanding naturally existing materials due to its distinguishing thermal and mechanical properties. As it is known as the hardest material, diamond has been a field of interest in plenty of mechanical studies and has taken its place in industry for different uses, as well. In the last few decades, with the pursuit of adaptation of semiconductors to the technology, the search for more durable novel materials with manipulative electronic characteristics has ascended. Thus, diamond has been one of the most popular research areas, such as the synthesis processes and surface studies, including scanning probe microscopy. Atomic Force Microscopy (AFM) studies of both natural and CVD grown diamond surfaces revealed the topography of diamond surfaces with different surface orientations and reconstructions. Besides, Scanning Tunneling Microscopy (STM) studies of diamond have shown that the electronic structure of diamond is highly related to the type of dopants and surface termination. In this study, the diamond surface has been investigated using simultaneous Scanning Tunneling/Atomic Force Microscopy in ultra-high vacuum (UHV). The investigation of diamond using simultaneous STM/AFM in UHV has been focused on polycrystalline and single crystalline diamond surfaces. The cleaning techniques including the sputtering, annealing and acid etch have also been practiced, in order to obtain atomically clean and flat diamond surfaces. The simultaneous STM/AFM system used in this study operates as using the tunnel current as the feedback parameter. By oscillating the cantilever at a specific frequency well below its resonance frequency, oscillations with sub-Ångström amplitudes were obtained. The detection of such small cantilever oscillation amplitudes was enabled by using a fiber-optic interferometry setup. Scanning the surfaces using such small cantilever oscillation amplitudes enables the true simultaneous STM/AFM operation on the diamond surfaces, by the means of being at certain operating regimes while scanning the surface. With the simultaneous STM/AFM system used in this study, surface topography, force, interaction stiffness, tunnel current modulation (measure of barrier height), phase shift (energy dissipation) and tunneling current were obtained. In this study, the diamond surfaces were scanned using two different cantilevers, a Tungsten (k=53 N/m) and a highly boron doped diamond cantilever (k=70 N/m), which were calibrated using thermal noise method. Atomic resolution imaging of different regions on diamond surfaces was achieved. Moreover, force-distance spectroscopies were conducted on different regions on the diamond surfaces, leading to obtain the interaction stiffness between the diamond and the tip. The maximum negative interaction stiffness between the polycrystalline diamond surface and the W tip is measured around -2-2.5 N/m, where the interaction stiffness between the polycrystalline diamond surface and the highly boron doped diamond tip is measured as -1.2 N/m. For the single crystalline diamond, the maximum negative interaction stiffness between the sample surface and the W tip is measured as -2.5 N/m and -1.2 N/m, with an applied bias voltage of -1 V and 1 V respectively. The maximum negative interaction stiffness between the single crystalline surface and the highly boron doped diamond tip is measured as -1.5 N/m.

İpen Demirel
İstanbul Technical University · Institute of Graduate Studies in Science
2018
00
Master'sOpen AccessEN

Optimization of optical and electrochemical properties of PANI, PEDOT conducting polymers to design electrochromic device

Advances in natural sciences and technology dominate creative ideas by giving new pathways for the future aspects of developments in electrochromism. Diving deeper in the materials' molecular structures conceives new problems and opportunities to create valuable information about innovative technologies. Organic materials have promising applications because of their specific properties such as durability, lifetime, low costs, low energy consumption, high ion diffusion, and easy and fast production methods. Therefore, organic materials are used in electrochromic applications to manufacturing functional devices as smart materials. In this project, polymer materials were characterized by CV, CA and impedance spectroscopy methods to use electrochromic applications. PANI and PEDOT materials are mostly used organic substances to develop interesting device prototypes like electrochromic devices, storage devices, and sensors. They were characterized using different methods and experimental results to improve their electrochromic and structural properties. In addition to the improvement process, heat-treatment effect and impedance properties were investigated and equivalent circuit models of developed materials and devices were created using IVIUMSOFT software. Polyaniline comes into prominence by electrochromic properties than other materials. It has three different oxidation states and each state has own color, which is why we used it for electrochromic applications. PANI was synthesized by using different parameters such as an acidic solution, concentration and annealing temperature, voltage ranges, and the scan rate of the voltage. Polyaniline is a unique polymer. It has three oxidation states showing different colors that are yellow, green, blue and their shades that is why polyaniline was chosen for electrochromic applications. It was characterized by electrodeposition and chemical oxidation methods. Electrodeposition method has the capability to polymerize aniline but the strength and lifetime are too low because of adsorption and fast degradation under the room conditions. From this point on, heat treatment was applied to improve electrochemical properties and lifetime of polyaniline films. Advancing in parallel with this process, the chemical oxidation method was carried on to develop polyaniline films. Polyaniline films, which are heat-treated at 90oC, that were coated using the electrodeposition method. They were reached to the better parameters as polyaniline films, which are deposited by chemical oxidation method. Heat-treatment was not applied to polyaniline films developed using chemical oxidation methods because of a quite high lifetime and high adsorption properties. The unique property of chemical oxidation method is that coated films do not require conducting surface in the coating process. Chemical oxidation method was carried on stable room conditions and bath has 15oC using APS as an oxidizing agent. PEDOT films were developed by electrodeposition method onto the ITO surface. 3, 4-ethylenedioxythiophene was used as monomer prepared in acetonitrile/LiClO4 mixing solution. Compensating required ion transportation in the solid electrochromic device is the reason why PEDOT films, the counter electrode, are required to develop. For this respect, optimum parameters found in the experimental processes to polymerize EDOT onto the ITO surface. PEDOT films were found more conducting than PANI films when calculating total charge transportation in chronoamperometry measurement. If these results are taken into consideration, PEDOT films have more conductivity and have more capability for electrochromic application than PANI films. Electrolytes are important materials for electrochromic devices. Characterization of electrochromic films was carried out in solution based 3-probe cell system. PANI film was characterized in acidic media and PEDOT films were characterized in alkaline media. This is the key difference between the two films. Acid includes H+ ions but base that was used for characterization of PEDOT includes Li+ ions. These ions diffuse through the films in electrochemical processes and they show electrochromic properties after diffusion, which causes redox reactions and protonation/deprotonation processes. Gel or solid electrolytes that include ionic structures are used in solid electrochromic devices and they are the basic requirements in a diffusion process to observe electrochromic properties. In PANI/PEDOT solid device application process, durability is controlled in chronoamperometry measurement. It has a very long lifetime, which is higher than ten thousand cycles, but contrast change is quite low due to the transition of color change. The color of the PANI films toggles bleach to green/blue when voltage sweeping negative to positive but PEDOT works inversely. Positive to negative transition could not be observed easily in color change. Nevertheless, it is not the only reason to disparage PANI/PEDOT solid device also electrolyte gel layer is an important parameter for ion transportation between electrodes. It was made of LiClO4 and PMMA mixing structure in PC solution that is well-known electrolyte in such electrochromic applications. Finally, after the investigation of electrolyte for both cell and solid electrochromic devices, optical and electrochemical properties of the optimized organic films were experienced using spectroscopic, cyclic voltammetry and chronoamperometry methods. Then, coloration efficiency, diffusion constants, optical and electrical properties were determined using the required mathematical and physical tools depend on the measurement parameters and results. In the last step, the equivalent circuit model was studied using electrochemical impedance spectroscopy method using obtained data in the measurements. Under the guidance of these results, future applications of studied materials were considered to open a new path for both electrochromism and other potential applications.

Semiconductor thin films
İsmail Bütün
İstanbul Technical University · Institute of Graduate Studies in Science
2018
00
DoctorateOpen AccessTR

Skaler bozon aracılığıyla üst kuarkın çeşni değiştiren yüksüz akım etkileşmelerinin araştırılması

Günümüzde yüksek enerji fiziği, Standart Model (SM) çerçevesinde Higgs bozonunun da keşfedilmesiyle birlikte yeni bir evreye girmiştir. Bu evrede bilim insanları günümüze kadar ortaya konmuş olan modelin çözümlenmemiş problemlerine odaklanmıştır. Buradaki sorunların kesin çözümleri ise tartışmasız deneysel doğrulamaya muhtaçtır. Öte yandan Büyük Hadron Çarpıştırıcısı (LHC)'ndan elde edilen sonuçlar, SM'in sorunlarının çözümüne yönelik olarak öne sürülen hiçbir SM ötesi modeli doğrulayamamaktadır. Bu durum araştırmacıları daha yüksek enerjili hızlandırıcılarda yapılacak deneylerden elde edilecek verilerde yeni fizik arayışına itmektedir. Teze konu olan bu çalışmada SM'in cevapsız bıraktığı sorulara cevap bulmak amacıyla, çeşni değiştiren yüksüz akım (FCNC) türündeki etkileşimlerin yeni çarpıştırıcılardaki gözlemlenme potansiyeli, etkin alan teorisi çerçevesinde ve benzetim yöntemi kullanılarak araştırıldı. Bu doğrultuda şu anda sıklıkla çalışılan üst kuarkın anormal etkileşimleri incelendi. Bu çalışmalardan elde edilen öngörülerin deneylerle sınanması hiç kuşkusuz işin en can alıcı kısmını teşkil etmektedir. Bu tip etkileşmelerin deneysel ölçümleri çok hassastır ve öngörüler kolaylıkla test edilebilir niteliktedir. Dolayısıyla deneylere de yön gösterecek bu tipte çalışmalarla, olası yeni fizik keşiflerine ya da etkileşme sabitleri üzerine yapılabilecek dışarlamalara kapı açılması mümkündür. Bu bağlamda tezde, üst kuark ve Higgs bozonunun FCNC etkileşimi önce Yüksek Işınlıklı Büyük Hadron Çarpıştırıcısı (HL-LHC)'de aynı işaretli lepton kanalında incelenmiş ve kanalın dışarlama için uygun olduğu kanaatine varılmıştır. Dışarlama senaryosu için etkileşim sabiti \eta_{q}=0,04 ve karşılık gelen dallanma oranı HL-LHC beklentilerine uygun olarak 3,048\times10^{-4} olarak elde edilmiştir. Daha sonrasında FCC-hh için yapılan araştırmada ise keşif senaryosu için \eta_{q}=0,0059 ve karşılık gelen dallanma oranı 1,32\times10^{-5} ve dışarlama senaryosu için \eta_{q}=0,0027 ve karşılık gelen dallanma oranı 2,78\times10^{-6} olarak bulunmuştur.

Higgs bozonuKuarkSkaler+2
Özgün Mustafa Özşimşek
Hacettepe University · Institute of Graduate Studies in Science
2022
00
Master'sOpen AccessTR

RF magnetron kopartma tekniği ile büyütülen LiCoO2 ince filmlerin optik, elektrokromik ve yapısal özelliklerinin incelenmesi

Dünya nüfusunun hızlı bir şekilde büyümesiyle, dünya çapında fosil enerji kaynaklarına ihtiyaç artmıştır. Fosil temelli enerji kaynaklarının kullanımı sonucunda dünya, küresel ısınma, sera etkisi, ozon tabakasının delinmesi gibi problemlerle karşı karşıyadır. Teknolojinin ilerlemesi ile birlikte alternatif ve yenilenebilir enerji kaynaklarına yönelim başlamıştır. Elektrokromik malzemeler, bir elektriksel gerilim altında optik özellerini tersinir olarak değiştiren malzemelerdir. Elektrokromik malzemelerde görülen bu tersinir mekanizma elektrokromizm olarak adlandırılır. LiCoO2, hali hazırda yeniden sarj edilebilen pillerde kullanılan bir malzemedir. Yüksek verimli kapasitör özelliği taşıyan LiCoO2 malzemesinin, ince film formunun kullanım alanlarının araştırılması gereklidir. LiCoO2 ince filmlerin katıhal elektrokromik cihazlarda kullanılmabilmesi için, büyütme parametrelerinin elektrokromik özelliklerine ve renklenme mekanizmalarına nasıl etki ettiği tam olarak anlaşılmalıdır. Bu çalışmada, LiCoO2 ince filmler RF magnetron kopartma tekniği ile cam alttaşlar üzerinde büyütülmüştür. Büyütülen LiCoO2 ince filmlerin elektrokromik ve optik özelliklerine film kalınlığının, kısmi oksijen basıncının, plazma gücünün, alttaş sıcaklığının etkileri incelenmiştir. Bu tez çalışmasında optik renklenme gözlenen örneklerin optik modülasyon ve renklenme verimlilikleri hesaplanmıştır. Yapısal özellikleri X-ışınları kırınımı ve atomik kuvvet mikroskobu ile tayin edilmiştir. Yüzey görüntüleri taramalı elektron mikroskobu ile alınmıştır. Örneklerin elektrokromik analizleri yapılırken, gerilim ve zamana bağlı akım çevrimsel voltametri ve kronoamperometri ölçümleri alınmıştır. Elde edilen kronoamperometri eğrilerinin altında kalan alanlar hesaplanarak elektrokimyasal çevrimler boyunca film yüzeyine giren ve çıkan yük miktarları hesaplanmıştır. Tez kapsamında büyütülen LiCoO2 ince filmlerin elektrokromik olarak zayıf renklenme göstermekle birlikte, elektrokimyasal prosesler boyunca gözlemlenen iyon giriş ve çıkış kapasitelerinden dolayı katıhal elektrokromik cihazlarda iyon iletken tabaka olarak kullanılabileceği ön görülmüştür. Anahtar Kelimeler: LiCoO2 ince filmler, RF magnetron kopartma, elektrokromizm, renklenme verimliliği, optik modülasyon

Buğrahan Erbar
Hacettepe University · Institute of Graduate Studies in Science
2020
00
Master'sOpen AccessTR

Protein-ligand etkileşimlerinin kuantum mekaniksel/moleküler mekaniksel simülasyon teknikleriyle incelenmesi

Bu çalışmanın temel amacı, metal iyonu bağımlı biyomoleküler sistemlerin in silico kuantum ve moleküler mekaniksel hibrit yaklaşımlarla (QM/MM) araştırılmasıdır. İnhibitör bağlı enzim yapısı üzerinde yapılan deneysel çalışmalarla tahmini yapılan doğal substratların izlediği reaksiyon konformasyonlarının hesaplamalı olarak belirlenmesi hedeflenmiştir. Moleküler dinamik (MD) ve Metadinamik (MTD) simülasyon yöntemleri kullanılarak yürütülen bu araştırmada, bir insan bağırsak ortakyaşarında bulunan Kalsiyum (Ca2+)-bağımlı alfa-mannosidaz enziminin iki inhibitör ve bir doğal substrat alfa-1,2-Mannobiyoz'u içeren üç yapısı incelenmiştir. Doğal substratı içeren yapıda şeker halkasının Cremer-Pople büzüşme koordinatları kullanılarak QM/MM MTD çalışmalarla elde edilen serbest enerji yüzeyleri, hesaplamalı çalışmalarımız ile deneysel bulguların reaktant ve geçiş hali konformasyonları etrafında uyumlu olduğunu göstermektedir. Reaktant ve geçiş hali konformasyonları tespit edilen doğal substrat bağlı yapının aktivasyon enerjisini, reaksiyon enerjisini, metal iyonunun rolünü ve substratın reaksiyon sırasında izlediği konformasyonel yolu belirleyebilmek için farklı parametrelere sahip bir dizi QM/MM MTD hesaplamalar yapılmıştır. Çalışmada kullanılan yöntem ve yaklaşımlarla elde edilen bilgiler, glikozidazların katalitik mekanizmaları üzerindeki bilgimizi genişletecek ve bir lizozomal depolama hastalığı olan alfa-mannosidoz hastalığının teşhis ve tedavisi için analogların tasarlanabilmesine katkıda bulunma potansiyeline sahip olacaktır.

Bilgisayar destekli hesaplamaKarbonhidrat metabolizmasıKuantum mekaniği+3
Mert Sağıroğlugil
Hacettepe University · Institute of Graduate Studies in Science
2021
00
DoctorateOpen AccessTR

Düşük yayıcı kaplama tasarımı, hazırlanması ve karakterizasyonu

Birçok ülkede üretilen enerjinin % 40'ından fazlası binaların ısıtılması ve soğutulması için harcanmaktadır. Binalarda enerji tüketiminin azaltılması pencere camlarının kızılötesi radyasyon geçirgenliğinin ve yansıtmasının kontrol edilmesiyle mümkündür. Enerji-verimli cam kaplamalarından biri olan düşük yayıcı kaplamaların kullanım amacı, yaşam alanının içi ile dış ortam arasındaki ısı transferini azaltmaktır. Bu tez çalışmasında, dielektrik/metal/dielektrik (D/M/D) şekillenimine sahip düşük yayıcı kaplamalar tasarlandı ve hazırlandı. Düşük yayıcı kaplamaların metalik/metal katmanı olarak, farklı büyütme koşullarında hazırlanan, titanyum nitrür (TiNx) veya gümüş (Ag) ince fimler, dielektrik katmanı olarak ise elmas-benzeri karbon (DLC) veya alüminyum-katkılı çinko oksit (AZO) ince filmler kullanıldı. TiNx ve DLC ince filmler DC magnetron kopartma yöntemiyle, Ag ve AZO ince fimler ise RF magnetron kopartma yöntemiyle, cam alttaşlar üzerinde büyütüldü. Hazırlanan ince filmlerin optik ve yapısal karakterizasyonu yapıldı. Film büyütme koşullarının filmlerin optik özellikleri, bağlanma özellikleri, mikroyapısı, faz bileşenleri ve kızılötesi yayma oranları üzerindeki etkileri UV-VIS-NIR spektrofotometre, XPS, Raman spektroskopisi, SEM, AFM, XRD ve FTIR ölçümleriyle incelendi. TiNx, Ag, DLC ve AZO ince filmlerin (s ve p kutuplu ışık için) ölçülen optik geçirgenlik ve optik yansıtma spektrumlarına, eş zamanlı olarak, uygun kuramsal optik modellere benzetişim (eğri çakıştırma işlemi) yapılarak, filmlerin optik sabitlerinin dalgaboyu ile değişimi, kalınlıkları ve tabaka dirençleri elde edildi. Bu yöntemle bulunan film kalınlıkları ve tabaka dirençleri, sırasıyla, profilometre ve standart dört nokta kontak yöntemleri ile doğrulandı. Ayrıca, film büyütme koşullarının AZO filmlerin kızılötesi dalgaboyu aralığında optik yansıtmasına etkisi ayrıntılı olarak araştırıldı. Düşük yayıcı kaplamalarda metal katman ve dielektrik katman olarak kullanan filmler için optimum büyütme koşulları belirlendi. Bu filmler cam alttaş üzerinde D/M/D şekilleniminde büyütülerek, farklı metal (TiNx veya Ag) ve dielektrik katmana (DLC veya AZO) sahip düşük yayıcı kaplamalar üretildi. Bu kaplamaların düşük yayıcı performansları (görünür bölgede yüksek optik geçirgenlik ve kızılötesi bölgede düşük yayma oranı) birbiriyle ve literatürde yer alan düşük yayıcı kaplamaların performansları ile karşılaştırıldı. Bu çalışmada, kızılötesi bölgede en küçük yayma oranı (ϵ=0,027) AZO/Ag/AZO düşük yayıcı kaplama için elde edildi. Bu kaplamanın uzun-dalgaboylu ısıl radyasyon dalgaboyu aralığında optik yansıtması yaklaşık % 97 ve görünür bölgedeki ortalama optik geçirgenliği yaklaşık % 75'dir. Sahip olduğu bu özellikler nedeniyle, AZO/Ag/AZO kaplama enerji-verimli binaların camlarında kullanılabilir.

GümüşTitanyum nitrürİnce filmler
Meltem Babayiğit Cinali
Hacettepe University · Institute of Graduate Studies in Science
2019
00
DoctorateOpen AccessEN

Electric and magneto-transport properties of magnetic and superconductive iron pnictide and skutterudite compounds

Superconductivity has gained its popularity after the high Tc materials have been explored. Cuprates (copper-oxide systems) and Hg based 1223 systems still have research interest allowing to examine new chemical compounds for high Tc superconductors (HTS). Unconventional materials such as Fe-based pnictides (group V-B elements in 122 systems) are frontier compounds in which magnetism and superconductivity can be observed together in these materials, presenting them as an option for high Tc superconductors. Iron-arsenide (Fe-As) and copper-oxide (Cu-O) layers in the structure of a crystal are responsible for the superconductivity phenomenon observed in these systems. Fe-As system has similar properties with Cu-O like having d electrons, layered structures and antiferromagnetic (AFM) spin ordering and they are still earning interest. In addition to this, iron has a magnetic moment which plays a key role in superconductivity-magnetism colleration. Up to now, two physical problem in our study are the superconducting phase transition temperature Tc and magnetic behavior of superconducting materials. Lattice changes, symmetry breaking in the unit cell, applying pressure are some of reasons that shift Tc up or down. For the magnetic behavior of superconductive samples, establishment of a new magnetic ordering is key parameter under the Tc. Magnetic changes are said to be affect superconductivity. The exclusion of magnetic field lines by Meissner effect is a clear evidence for superconductive mechanism. Our study here is focused on iron pnictide compounds on the basis of these two physical problem. The most popular iron pnictide systems are Fe-As based ones. The material BaFe2As2 has a tetragonal structure and it goes a structural phase transition from tetragonal I4/mmm to orthorhombic Fmmm lattice. Same behaviors are found in AFe2As2 (A:Ba, Sr, Ca, etc.) systems at low temperatures like in cuprates. This kind of phase transition is named as spin density wave (SDW) transition and it is valid for both cuprates and iron-pnictides. A chemical change in composition with a dopant or applying pressure results magnetic transition in Fe-As compounds and thereby superconductivity emerges. By doping electron or hole to a AFe2As2 system like BaFe2-xPtxAs2 , superconductivity can be observed. Since the change in chemical composition may effect the Tc, Lanthanum is doped to the BaFe2-xPtxAs2 system. And a new serie of Ba1-xLaxFe1.9Pt0.1As2 polycrystalline samples are successfully synthesized by a solid-state reaction method. The synthesis of Pt and La doped compounds was physically remarkable since some of them are synthesized for the first time. Data obtained from those samples are investigated in detail by Rietveld refinement. Our target to produce "single phase" polycrystalline samples is achieved successfully. Unit cell parameters and symmetry group of samples are determined in agreement with the literature. Structural analyses of samples are made by X-Ray diffraction after the chemical synthesis part. Results are analyzed by FullProf software. Profile matching are done for whole samples and structural parameters are determined. Some samples are found single phase in which we published in the articles during our study. Resistivity measurements are performed with the liquid nitrogen followed by liquid helium by the help of a hand made glass cryostat. It is seen that the temperature dependence of the resistivity for the parent sample, BaFe2As2 exhibits the same behavior including a very close match to reported values given in the literature. The structural phase transitions from tetragonal I4/mmm to orthorhombic Fmmm lattice in BaFe2As2 and BaFe1.9Pt0.1As2 samples are observed. Temperature dependent transition is compatible with the corresponding phase changes observed at XRD measurement, which is known to be tetragonal at room temperature. Superconductive phase transition temperature, Tc for the samples in different Pt doping levels is investigated in the literature. It is found that Pt doping is effective on the change of Tc at lower doping rates like x = 0.2. x=0 sample is the parent sample (BaFe2As2) in which it is not superconductive but the BaFe1.9Pt0.1As2 sample has the highest value in Pt doped group for phase transition temperature, Tc. In addition to the literature, we revealed that superconductivity can be observed even in x=0.3 doping rates in such materials. Lanthanum doped samples are successfully synthesized in addition to the Pt doped ones. And resistivity measurements are showed that superconductivity still can be observed in such tetragonal I4/mmm systems. Resistivity of these samples are showed a clear evidence for superconductivity that our results approve. The magnetic measurements of materials are done by measuring zero field cooling (ZFC) and field cooling (FC) curves. Critical temperature, critical current density, coherence length (also known as Ginzburg-Landau parameter), volume magnetization and magnetic susceptibility values are obtained from the analysis. Magnetization behavior of samples are observed as a function of temperature and phase transition temperatures are determined. The critical current density, which is remarkable sign for how much charge a superconductor can carry, is estimated by models given in the literature. Coherence length is calculated from the M-H curves (from the Meissner effect observed in these samples). Results show that samples based on a tetragonal structure are convenient to be a host material for the superconductive behavior. This means the doping of rare-earth ions to those samples provide materials that have characteristic properties like showing zero resistivity and the exclusion of magnetic field lines. In our study, platinum and lanthanum are doped to our host material, BaFe2As2; and new sample sets are prepared. It is seen that ZFC-FC curves are separated in the phase transition temperature, Tc, showing superconductive behavior compatible with the resistivity measurements. Meissner effect is observed in both platinum and lanthanum doped samples. Critical current densities are calculated from the magnetic measurements and phase transition temperatures are determined. The samples are in superconducting regime where their temperatures are lower than the Tc. M versus H curves are measured in several temperatures in this regime below the phase transition temperature. Analysis of the results helped us to calculate coherence length z for the samples by obtaining Hc readings at different measurement temperatures. From the M-H curves of samples measured below the Tc, lines are extrapolated to T=0 K and coherence lengths are found in nm range. By transforming magnetization from emu/g to volume magnetization, susceptibility for the samples are obtained in terms of magnetization data. The termination of ZFC and FC curves in to close values to -1 in y axis, shows that samples are mostly diamagnetic with a high volume fraction. Samples are mostly presented superconductivity in general. Phase transition temperatures found from ZFC-FC curves are compatible with the resistivity data. La doped samples are showed a clear evidence for superconductivity that both resistivity and magnetic results approve. Thin films of BaFe2As2 sample is prepared and the amorphous structure is proved by the XRD measurement. Resistivity of sample is measured between 4.2-300K at liquid He. A phase transition at Tc = 6.7K is seen clearly with reproducible experiments which is very similar to a superconductive phase transition. We observe superconductivity for the first time in an amorphous thin film. This result is interesting because current macroscopic theory of superconductivity is based on Cooper pairing mechanism. The drop of resistivity down to zero obeys filamentary superconductivity that is seen in literature in principle. The difference in our study is that we create a disorder in material and it is amorphous. This process is realized in a simple flash evaporation system under vacuum. This is important because same kind of samples are produced in molecular beam epitaxy (MBE) or similar systems that we are not able to. Some studies are reported that both in bulk and thin film samples, showing that it is possible to apply pressure to the system and create disorder. This method is a way in order to trigger the superconductivity in such systems. For the first time, we observe the superconductivity in an amorphous thin film above the liquid He temperature, at ambient conditions. Magnetic characterization of this sample still continues and results will be presented in an appropriate publisher. In case of any failure in preparing superconducting samples, antimony doped compounds are prepared. BaFe4Sb12 sample is prepared first. This sample is known as skutterudite compound in literature and it is thermoelectrically efficient. Since the synthesis was successful, the thermoelectric and magnetic properties of Pt substituted BaFe4 xPtxSb12 (x = 0, 0.1, 0.2) compounds were investigated in this part of study. Thermoelectric (TE) materials are available to capture a part of wasted energy that is rejected to atmosphere and convert it into the useful electrical power. The efficiency of a TE generator is strongly depending on the dimensionless figure of merit ZT, defined as ZT = S2sT/k where S, s and k are the Seebeck coefficient, electrical conductivity, total thermal conductivity (k = ke + kL where ke is the electronic contribution and kL the lattice contribution) and T stands for the absolute temperature. Efficient thermoelectric materials are required to have high electrical conductivity, high Seebeck coefficient and lower thermal conductivity. Filled skutterudites fulfill these requirements. In the past decade years, experimental and theoretical tremendous effort have been conducted on skutterudites compounds in order to optimize their TE and magnetic properties for enhancing ZT value further and characterize low temperature behavior. The filled skutterudites with chemical formula RT4M12 where R = alkaline earth and rare earth metal, T = Fe, Ru, and Os and M = P, As, and Sb have been studied extensively due to their both high TE performance and exotic magnetic properties. Even though, there are many reports in literature on thermoelectric and magnetic properties of RT4M12 family skutterudite compounds. There is still lack of understanding about correlation between magnetic and thermoelectric phenomena for these compounds. In this work, we aim for contribute to understanding of relation between two phenomenon by characterization low temperature magnetic and thermoelectric properties BaFe4-xPtxSb12 (x = 0, 0.1, 0.2) compounds. X-Ray diffraction, resistivity, magnetic measurements, Seebeck coefficient and thermal conductivity of samples are measured. Temperature depending resistivity shows that all samples show semi metallic behavior in the temperature range of 4.2 K to 300 K. Increases in resistivity with Pt content is interpreted as existing of different scattering mechanisms such as spin fluctuation and Kondo impurity in these compounds or decreasing hole concentration. Kondo minimum are confirmed by temperature dependence of logarithmic resistivity analysis at 2-50 K which might be due to local deformation in crystal structure as a result of spin fluctuation mechanism. Local minimum and maximum in Seebeck coefficient observed might be due to paramagnon drag or spin fluctuation effect in materials. Magnetic susceptibility for the compounds x = 0.1 and x = 0.2 show that there are two successive transition, paramagnetic to magnetic state at Tc = 48 K and short range magnetic to long range magnetic ordering at lower temperatures, however there is only one transition from paramagnetic to long range ordering transition in Pt free compound. The lattice part of thermal conductivity versus temperature plot shows that the major part of total thermal conductivity is dominated by lattice contribution. Local maximum & minimum in Seebeck coefficient versus temperature plot, Kondo minimum observed in logarithmic resistivity show that there is a close relation between magnetic and thermoelectric properties due to spin fluctuation effect in Pt substituted BaFe4-xPtxSb12 (x = 0, 0.1, 0.2) compounds.

Murat Sertkol
İstanbul Technical University · Institute of Graduate Studies in Science
2016
00
Master'sOpen AccessEN

Kesikli wigner fonksiyonu

In the final chapter, through Weyl ordering, continuous Wigner function is derived. Then, using proper assignments, discrete counterpart in discrete phase space is introduced. First computing for single qubit and a pair of qubits, smallest contextual bit qutrit's discrete Wigner function is calculated both for a specific and a general initial condition. For a specific state, it has been shown thatWigner function can indeed have negative values as a quasi-probability distribution. Negative probabilities and their link to contextuality is discussed. As a result, if a qutrit's 6 tables can have at least one negative value for the general initial condition, it will mean that contextuality and negative probabilities are directly linked.

Merve Giray
İstanbul Technical University · Institute of Graduate Studies in Science
2017
00
DoctorateOpen AccessEN

Sorting of biological cells in a microfluidic channel using holographic optical tweezers combined with raman spectroscopy

Investigation of single cells is crucial, since the measurement from population gives an average value that does not necessarily represent every individual in the population. Besides, sorting and sometimes counting the desired kind of cell is a measure of how the concentration of that cell. These types of micro-scale measurements are sometimes necessary, for example, to monitor the cell cycle, cell-signaling processes. Serving to these purposes, first a holographic optical tweezers (HOT) setup was constructed. This setup was built by improving the current optical tweezers setup in the Laser Spectroscopy Laboratory in Istanbul Technical University. A brand new Holoeye Spatial Light Modulator (SLM) was installed in the system after it was calibrated using an interferometric setup. The holograms were calculated using a Gratings and Lenses algorithm written in MATLAB and implemented by the homemade GUI that manages all the tasks needed for trapping and spectroscopy. The test particles to characterize the HOT setup were polystyrene (PS) particles. An array of four trapped PS particles was manipulated to the Raman spectrum measurement region by the software. The software communicates with the spectrometer and obtains multi-track spectra from the array that gives individual Raman spectra of each particle. These spectra identified by the software using the correlation coefficient of this measurement with the dataset that has already been prepared using PS particles and yeast cells. The test Raman measurements of biological cells using yeast cells and E.coli cells were made to investigate the signal level in low exposure times. The measurement showed that, our system would not respond enough signal to classify particles when the sample is E.coli and the exposure time is one second. However, the yeast cells responded better in short exposure time. Considering these, the sorting test experiments were made using yeast cells and PS particles. In a mixed solution of PS particles and yeast cells, an array of four particles whose members are randomly chosen was moved to the measurement region. According to the measurement and the following classification, the particles are targeted to the previously defined positions in the measurement cell. In these experiments, classifications were made with success. A study to determine the embryo quality by Raman spectroscopy was made in collaboration with Istanbul University Medical School. In this study, it was aimed to find an objective method to assess embryo viability. The preliminary results showed that the sensitivity and specificity of these measurements are %93 and %77, respectively. A Mann-Whitney U test was applied on the band areas and all band area ratios obtained by band component analysis. The most significant one was found to be the band area ratio of 903/942 cm-1. Comparing the measurements of amino acids samples, it was determined that glutamine, glycine, proline, and valine has the most intense bands in the region that includes these significant bands. Among these, glutamine and glycine are the amino acids that contribute to embryo development most, according to the literature.

Uğur Parlatan
İstanbul Technical University · Institute of Graduate Studies in Science
2017
00
DoctorateOpen AccessTR

Yüksek enerjili, şekillendirilmiş lazer hüzmeleri ile saydam malzeme işleme ve karakterizasyonu

Femtosaniye (fs) darbeli lazerler etkin oldukları son derece kısa zaman süreçleri sayesinde benzersiz fiziksel özellik ve uygulama potansiyellerine sahiptir. Özellikle lazer-madde etkileşimi ve malzeme işleme alanında fs darbeli lazerler yeni bir çığır açmışlardır. Bu tez kapsamında fs lazer hüzmelerinin uzamsal ve zamansal olarak şekillendirilmesi, karakteristikleri ve saydam malzemeler ile olan etkileşimlerinin yanısıra mikroakışkan uygulamalarındaki kullanımları yer almaktadır. Tez kapsamında gerçekleştirdiğimiz çalışmalarda öncelikle Bessel ve Airy hüzmelerinin kuramsal incelemesini gerçekleştirdik. Ardından bu hüzmeleri deneysel olarak ürettik ve şiddet profillerini, ilerleme özelliklerini inceledik. Daha sonra fs lazer kullanarak bu hüzmelerin saydam malzemeler ile olan etkileşimlerini ortaya koyduk. Fs lazerlerin en çok kullanıldığı bir diğer uygulama alanı mikroakışkanlardır. Çalışmalarımızda fs lazer ile süperhidrofobik yüzey üzerinde ve aerojel kitle içerisinde mikroakışkan sistem üretimini, PDMS çip içerisinde damla temelli mikroakışkan sistem üretimini gerçekleştirdik. İlk olarak süperhidrofobik yüzey üzerinde hidrofilik mikrokanallar oluşturduk. Bu mikrokanallar üzerinde sıvı filament oluşturduk ve dalga kılavuzu özelliklerini inceledik. Ardından eşsiz özelliklere sahip hidrofobik silika aerojel içerisinde üç boyutlu mikrokanalı malzemeye zarar vermeden oluşturmayı başardık. Bu kanalın optoakışkan özelliklerini inceledik. Buna ek olarak PDMS çip içerisinde damla temelli sistemlerin fs lazer ile üretilebileceğini gösterdik. Zamansal olarak şekillendirilmiş lazer hüzmelerinin malzeme ışık etkileşiminde yüksek polarizasyon bağımlılığı gibi oldukça ilginç özellikleri mevcuttur. Bu özellikler uzay zaman bağlantıları (UZB) olarak adlandırılan etkiler kapsamında açıklanabilir. Bu çalışmada UZB etkilerini kontrollü olarak değiştirerek saydam malzeme işleme üzerindeki etkilerini ayrıntılı olarak inceledik ve fiziksel detaylarını ortaya koyduk. Sonuç olarak bu tez kapsamında gerçekleştirilen çalışmalarda ultrahızlı lazer- saydam malzeme etkileşiminin anlaşılmasının bilimsel değeri oldukça yüksektir.

Berna Morova
İstanbul Technical University · Institute of Graduate Studies in Science
2017
00
Master'sOpen AccessEN

Tunnelling induced photon emission from surface/interface systems of graphene on copper

Imaging with the smallest order of magnitude has always been an essential topic for researchers working in various areas. Especially with the invent of Nobel Prize winner scanning probe microscopy (SPM), investigations in nanoscopic scales have been performed in terms of topographic, electronic, magnetic and optical properties. In this thesis, we have focused on electronic and optical properties of surfaces using photon scanning tunnelling microscopy (pSTM). Light emission from a planar junctions such as Metal-Insulator-Metal systems attracted noticeable attention. These studies have indicated that surface plasmons are the dominant mechanism of this light emission. Surface plasmons has been defined as collective oscillations delocalised electrons which propagate electromagnetic waves along the conducting surfaces. There might occur different modes of surface plasmons e.g. surface plasmon polariton (SPP) and localised surface plasmon (LSP). SPP defines surface plasmons which are propagating electromagnetic waves along the surface. LSPs are the charge oscillations in the gap plasmons. However, it was also reported that SPPs might be arise by LSPs as well. With the invent of scanning tunnelling microscopy (STM), photon emission from tunnel junction was applied in nanoscopic scales as well. Photon emission investigations have been performed on surfaces such as noble metals, molecule adsorbed metals, thin film combinations etc.with pSTM systems. Although some allotropes of carbon have been investigated in pSTM studies, graphene has not been stated yet in these investigations. In our work, we have focused on photon emission characteristics of chemical vapour deposition (CVD) grown graphene/copper structure. Graphene is a promising two dimensional material having honeycomb lattice. Several studies have revealed its extraordinary electronic, mechanical and optical properties. On the other hand, graphene can protect where it covers like a shield against exposing to corrosion. In our study performed under ambient conditions, graphene protects copper substrate from oxidation. Certainly the electronic properties of copper has be considered in this investigation. In this work, photon emission from metal-tunnel junction-graphene/metal system under ambient conditions was first reported. It was clearly seen that crystal orientation of copper facets has a dominant role on this tunnelling induced luminescence from Graphene/Cu sample. Based on measurements, it was determined that the occurrence of free electron surface state of Cu(111) surfaces are decisive in photon emission.

Hakkı Tunç Çiftçi
İstanbul Technical University · Institute of Graduate Studies in Science
2017
00
Master'sOpen AccessTR

Sıvı kristal ikili karışımlarında Halperin-Lubensky-Ma ölçeklenme fonksiyonunun çift kırıcılık ölçümleri ile test edilmesi

Sıvı kristal hali maddenin ara hallerinden biridir. Sıvılar izotropiktir yani her yönde aynı özellikleri gösterir. Kristal katılarsa anizotropiktir, birçok fiziksel özelliği yöne göre farklıdır. Sıvı kristal fazında ise birçok fiziksel görünüm olarak sıvıya benzeseler de, molekülleri aniztropik özellikler gösterecek şekilde düzenlidir. Sıvı kristaller iki çeşittir, birincisi liyotropik sıvı kristaller, diğeri ise termotropik sıvı kristallerdir. Liyotropik sıvı kristaller ara fazlarını çözücü konsantrasyonuna bağlı olarak gösterirler. Termotropik sıvı kristaller ise adından da anlaşılacağı üzere sıcaklığa bağlı olarak ara fazlar gösterirler. Bilimsel çalışmalarda termotropik sıvı kristaller en çok kullanılanlardır. Termotropik sıvı kristal moleküllerin konumsal yönelimsel düzenine göre farklı gruplara ayrılırlar. Temel olarak üç ana ara fazı bulunmaktadır; nematik, smektik ve kolesterik. Nematik sıvı kristaller uzun erimli yönelimsel düzene sahiptirler ve tercihli bir n ̂ (direktör) vektörü yönünde yönelirler. Smektik sıvı kristaller ise hem konumsal hem yönelimsel düzene sahiptirler ve katmanlı yapılarıyla karakterize edilirler. Tabaklar arası ve tabakanın içindeki korelasyona bağlı olarak smektiklerin farklı türleri vardır, keşfedildikleriyle sırayla alfabetik olarak (Smektik A, B, C…) kodlanmışlardır. Smektik A (SmA) fazındaki moleküller katmanlarda birbirine paralel olarak yönelmişlerdir, bu yönelim direktör yönündedir. Kolesterik sıvı kristaller kiral nematik sıvı kristallerdir, yani nematiklerden tek farklı moleküller sarmal şeklinde katmanlar halinde yönelmiştir. Faz geçişi maddenin dışarıdan bir etkiyle (sıcaklık ve basınç) bulunduğu fazdan başka bir faza geçmesidir. Faz geçişinde iki fazın birbirinden ayırt edilemediği noktaya "kritik nokta" buradaki sıcaklık ise "kritik sıcaklık" olarak adlandırılır ve T_C ile gösterilir. Eğer bir faz geçişinde gizli ısı ortaya çıkıyor ve entropinin süreksiz olarak değişiyorsa, bu birinci dereceden faz geçişi, entropi sürekli ve gizli ısı gerekmiyorsa ikinci dereceden faz geçişi olarak adlandırılır. Sıvı kristaller birçok ara faza sahiptir. Bu nedenle faz geçişleri konusunda birçok model ve teorilerin geçerliliği sıvı kristaller kullanılarak gösterilebilir. Bu çalışmada sıvı kristallerin bir anizotropik özelliği olan çift kırıcılık kullanılarak Nematik – Smektik A (N-SmA) faz geçişi civarında Halperin-Lubensky-Ma (HLM) teorisiyle uyumu incelenmiştir. Çift kırıcılık anizotropik malzemeden giren ışığın iki farklı ışığın kutuplanmasıdır, ∆n ile ifade edilir. Bu çalışmada çift kırıcılık ölçümleri yüksek hassasiyet özellikli döner analizör metotu yapılmıştır. Çift kırıcılık verileri kullanılarak nematik düzen parametresi daha önce Özbek ve ekibi tarafından gösterilen S(T)=Δn(T)/〖Δn〗_0 bağıntısıyla bulunmştur. Anisimov ve ekibi tarafından N – SmA geçişindeki düzen parametresi ψ ve direktör dalgalanmasının serbest enerjiye eklenmesiyle bu ifadeye kübik bir ifade eklendiğini göstermiştir. Bu kübik terim geçişin birinci derece olmasını gerektirir. HLM teorisinde de N – Sm A geçişi birinci derece olması gerekir. Daha sonra evrensel ölçeklenme fonksiyonunu konsantrasyon x ve S ̅ indirgenmiş entropi değişimi bağlı olarak S ̅/S ̅^* -(S ̅/S ̅^* )^(-1/2)=a ̂/S ̅^* (x-x^* )≡y-y^* ifadesiyle verilmiştir. Çetinkaya ve ekibi bu evrensel ölçeklenme fonksiyonundaki entropi değişimiyle N- SmA geçişinde nematik düzen parametresi S ilişkilendirmiştir. Bu çalışmada 8CB – 10CB ikili karışımlarında çift kırıcılık ölçümlerinden nematik düzen parametresi S, türetilmiştir. Bu S verileri T_NA N –SmA geçiş sıcaklığı civarında olası entropi süreksizliklerine ulaşmak için kullanılmıştır. Elde edilen mol kesri x'e bağlı entropi süreksizlikleri evrensel ölçeklenme fonksiyonuna iyi bir şekilde fit edilmiştir. Bu da HLM teorisindeki smektik A ve yönelimsel düzenin çiftlenimden dolayı kübik terim eklenen ortalama alan ifadesiyle tutarlıdır. Ayrıca daha önce yapılan kalorimetrik ölçümlerle bulunan sonuçlarla oldukça uyumludur. Daha sonra T_NA civarındaki S(T)'nin sıcaklık türevinin aynı kuvvet yasası ıraksaklığı (özgül ısı kapasitesi) olduğunu kullanılarak etkin kritik üstel değerleri bulunmuştur.

Şenay Üstünel
İstanbul Technical University · Institute of Graduate Studies in Science
2017
00
Master'sOpen AccessEN

Atomic and island scale diffusion events on Bi2Te3 (0001) surfaces & ultra-thin Bi2Te3 films on SiO2 substrates

Topological insulators (TI) are new phase of materials. They were reported as they have conducting surface states at their edges whereas they have insulating band in bulk. While Bismuth Telluride (Bi2Te3) is well-known thermoelectric material for several decades, it attracted attention again in recent years after declared as a TI. TI are promising materials in novel fields such as spintronics, quantum computation and topological superconductivity. Before any application in these fields, further investigations on their incompleted both morphological and electronic structure require. Bi2Te3 has rhomboherdral primitive cell which contains five atoms. It consists of five atomic planes of (Te1-Bi-Te2-Bi-Te1) along c-axis named as quintuple layer (QL). QLs are bind each other with weak van der Waals bonds, yields most cleavable interface. After cleaving, resulting Te1 terminated (0001) surface has trigonal lattice, and its both morphological and electronic structure can be determined at atomic scale by means of scanning tunneling microscopy (STM). In addition, Bi2Te3 has four type of defects. Depending on the doping type, types of the observable defects may change. In this thesis, we studied general morphology of (0001) surfaces of Bi2Te3 under ambient conditions with STM, including the defects and their electronic structure. In addition to investigations on morphological structure, we focused on diffusion events of the Te1 vacancies. To the best our knowledge, we report for the first time diffusion of individual atomic scale defects as well as Ostwald ripening of vacancy islands on a TI surface. Also, we investigated the nature of mass flow on Bi2Te3 surface according to previous studies that express the thermodynamic and kinetics behind growing islands. On the other hand, the knowledge on the electronic structure of this material at ultra-thin limit is still incomplete. We modified chemical vapor deposition (CVD) technique to grow ultra-thin Bi2Te3 films on SiO2/Si wafers. In this process, we obtained ultra-thin films and micro-particles of Bi2Te3. The heights of obtained Bi2Te3 films are measured to be a few QLs. The radius of Bi2Te3 micro-particles are few micrometers. Structural and spectroscopic characteristics of these ultra-thin films are also discussed.

Mert Taşkın
İstanbul Technical University · Institute of Graduate Studies in Science
2017
00
Master'sOpen AccessEN

Thin accretion disks around black holes modeling the secondary outburst

Accretion disks are efficient engines which convert gravitational energy into heat and radiation. Since it is not possible to observe a black hole directly, it is difficult to understand and probe the physics of such environments. Accretion disks may provide essential clues about the physics near such dense objects. If the secondary star in a low–mass black hole binary fills its Roche–lobe, matter will enter the gravitational influence of the black hole. Since the transfered matter will possess some initial angular momentum, it will start to orbit the black hole instead of directly fall onto it, hence, forming an accretion disk. Due to magnetorotational instabilities, eddies will form hence leading to enhanced viscosity. Due to the viscous torques, angular momentum will be transfered outwards, allowing matter transfer towards the black hole. The viscous dissipation in the disk will produce heat and also black body radiation in soft X–rays. Such a disk can be modeled as a viscous flow towards the black hole. It is possible to make relatively accurate models using the famous a–prescription for the viscosity. By taking advantage of the conservation of mass and angular momentum, a non–linear diffusion equation is obtained which describes the temporal evolution of accretion disks. In this work, this diffusion equation is solved numerically by implementing a finite differences scheme with Crank–Nicholson discretization. The disk instability model, which determines the stability regimes of various regions of the disk, is also implemented. Also, irradiation of the disk from a central source and irradiation by a lamppost–like source is included to the numerical model. The values of the opacities in the disk is determined by realistic opacity tables. In many observations of low–mass soft X–ray transients, it is seen that a secondary maximum occurs in the light curve during the decay phase. It is argued that the reason behind such a secondary outburst may be the formation of a radiating corona. It is proposed that the geometry of the corona, allows the previously shadowed parts of the disk to be irradiated, hence leading to an increase in mass flow towards the black hole. This, in turn, leads to a secondary outburst. The preliminary numerical results have been compared to Pringle's approximate analytical solutions to the disk equation. The results with different corona sizes, corona luminosities, and corona formation times have been obtained by using the HPC at Sabancı University. It may be possible to obtain clues about the geometry of the corona, which is still an unknown, by relating it with the observed secondary outbursts.

Mehmet Deniz Aksulu
İstanbul Technical University · Institute of Graduate Studies in Science
2017
00
Master'sOpen AccessEN

Investigation of swift heavy ion irradiated graphitic surfaces and novel graphene based devices

Tailoring materials with atomic scale defects have been studied over decades. In recent years, It had been understood that making a functional electronic device with extremely small size (several tens of nanometers) by use of novel materials such as graphene requires introducing defects. One way of achieving this goal is swift heavy ion (SHI) irradiation. In the first part of the study, we investigated defect formation on swift heavy ion (uranium and lead) irradiated graphitic surfaces by means of Scanning Tunneling Microscopy with a focus on HOPG and dislocated graphene layers on HOPG (moiré zones). Our results showed that structures that form on HOPG surfaces due to SHI irradiation in perpendicular geometry have a variety of shapes and sizes rather than just being hillock like. Moreover, comet-like structures were observed on HOPG surfaces due to SHI irradiation under 80o incidence angle with respect to surface normal. Obtaining atomic resolution on the tail section of the comet-like structures proved that SHI does not damage the surface layers while it is traversing in the bulk of the crystal. On the other hand SHI Irradiation of moiré zones under 80o incidence angle and SHI irradiation of moiré zones under grazing incidence (87.5o) did neither show destruction of the graphene layer generating the moiré pattern, nor any unzipping of the graphene as shown to happen on SHI irradiation of graphene crystals on dielectric substrates. Rather, the defects forming as a result of these lead and uranium irradiations were comet-like both on pristine HOPG samples as well as on moiré domains. Furthermore, irradiation of moiré zones with perpendicular geometry has been studied. It was observed that moiré zones may remain unharmed or they may locally destroyed upon SHI irradiation due to electronic changes in the bulk or moiré zone itself. We also studied tribological properties of SHI irradiated HOPG surfaces by means of Friction Force Microscopy (FFM). Our FFM measurements showed complementary results to our STM measurements. We observed that the head sections of the comet like structures appeared on simultaneously measured topography and friction maps. Intriguingly, tail sections of the comet-like structures appeared on friction maps, although they could not have been observed on topography maps. In some cases tails sections showed less friction compared to pristine HOPG surface. Our results showed that friction between two surfaces can also be a function of the bulk material. In the second part of the thesis, we demonstrated transparent heating element made out from Chemical Vapor Deposition (CVD) grown graphene on copper substrates. We used wet transfer method to transfer graphene on glass and quartz substrates for producing transparent heating element and modified transfer process for our purposes. Excitingly, our transparent heating elements can go up to high temperatures (310o C) with very low power consumption (27.2 Watt). We also studied heating properties of graphene samples grown by various growth paremeters. We observed that our graphene samples have monolayer background with multilayer zones. Also we observed silicon-oxide impurities may form on the CVD grown graphene and they can be transferred on any substrate. Changing growth parameters causes differences in the impurity concentration as well as monolayer and multilayer zone concentration which results in differences in heating properties of the graphene based heating elements.

Cem Kıncal
İstanbul Technical University · Institute of Graduate Studies in Science
2017
00
Master'sOpen AccessEN

Investigating the emission properties and the geometry of black hole X-ray binaries in the outburst cycle

Depending on their initial mass, stars can live from millions up to billions of years. This mass also determines the next step in their stellar evolution when they ran out of their fuel. The cores of stars with a mass greater than 20 M collapse into a black hole (BH). This object does not produce any radiation by itself, however, if it is in a binary system, the companion star may supply matter that accretes onto the BH. The angular momentum of the accreted material prevents a direct fall and matter forms a disk around the BH. The radiation from this accretion disk is observable. Under certain circumstances, a portion of this disk thought to evaporate by the effect of heat conduction and turns into a radiatively inefficient hot-flow. The relativistic electrons in the flow Compton-up scatter the disk photons and produce hard X-rays. The material in the disk may also be ejected away on some region close the BH with the help of strong magnetic field which produces the jets observed in radio and near-infrared wavelengths. These phenomena have a tendency to repeat themselves in a hysteresis-like loop. Constant monitoring of BH X-ray binaries provided a classification based on the abrupt changes in spectral and temporal properties of the sources. According to this classification, BHXBs spend most of their time in a low flux state known as quiescence. At the very beginning of the outburst, the system goes into a hard state in which the spectrum is dominated by high energy photons and variability increases. The compact jets are also observed in this state. As the material starts to move radially inward, the luminosity increases and variability drops. This state is known as the soft state. A disk wind may be observed in this state for high inclination sources. At the end of the outburst where mass accretion rate ( Ṁ) is sufficiently low, evaporation may remove majority of the disk which cause the source returns back into its initial state. There are also intermediate states which show properties of both hard and soft states with unique features. Unfortunately, there is no universal model that explains all the dynamic properties of BHXBs in different spectral states. Some models take into account GR effects and others include dynamo process as well as change in accretion rate. Interpretation of these models allows us to understand the motivation behind the observed phenomena. For instance, jets are events which usually are observed in hard and hard-intermediate states in a timescale of hours to months. Although the mechanism behind this phenomena is still debated multi-wavelength observations put forward a strong correlation between radio and X-ray luminosity indicating a disk-jet coupling. This nonlinear relation between inner flow and outflow (X-ray-radio luminosity) is thought to be simple and unique at first. Yet, along with the increase in the amount of data, it became clear that numerous BH systems are "outliers" follow a steeper path in radio X-ray correlation. Several models have been proposed to explain this strange behavior. One of the most promising hypothesis is the condensation disk model where it is assumed that a cooler weak disk is reformed at the end of the outburst which provides the additional X-ray flux. As Ṁ decreases the disk can no longer re-condense and disperse. The outliers which joins the main track below a certain flux value are considered to experience such a process. This hypothesis can be tested by determining the geometry of the system since the corona (hot-flow) must retrieve at some point in order to allow the inner disk to reform. The first part of this thesis is devoted to testing this hypothesis by modeling the power spectrum of both regular and outlier sources with a new developed model PROPFLUC. This is a physical model based on the mass accretion rate fluctuations in the precessing corona. Temporal analyses of sources with such a model allowed us to extract the inner and outer radius of the corona. By observing the evolution of these parameters we aim to understand how disk and corona behave relative to each other during outburst decay and rise. In this part, data from 4 different BH transients (GX339-4, 4U1543-47, GRO J1655-40, XTEJ1550-564) have been analyzed in hard and hard-intermediate states for multiple outbursts between 2000-2011. Raw data were obtained from the Rossi X-ray Timing Explorer (RXTE) and processed according to the procedure stated in the Guest Observer Facility of NASA-HEASARC. Analyses are generally done in both XSPEC and IDL programs and additional bash and TCL scripts were used to automate the processes. In the outburst cycle, the transition from hard to soft state occurs at higher luminosity compared to transition from soft to the hard state. The second part of this thesis covers the spectral and timing analyses of BHXBs in outburst decay in order to obtain the luminosity distribution of these sources. By exploring the key parameters of state transition, we aim to investigate the origin of hysteresis in the hardness-intensity diagram as well as investigating the variability of state transition luminosities for multiple sources in the outburst decay. The transition luminosities were found for 2 separate classifications in the literature namely Belloni and Kalemci classifications. The analyses were done for 12 BH transients in 20 outburst decays. The spectral fits were mainly done via tbabs*smedge*(powerlaw+diskbb) model. In addition, Gauss and hecut models also tested in order to include the effect of the iron line (emission around 6.4 keV) and the exponential cut-off in the power-law predicted by thermal Componization models. The timing part was mainly modeled with multi Lorentzians where broad-band noise and QPO corresponds to broad and narrow Lorentzians respectively.

Armın Vahdat Motlagh
İstanbul Technical University · Institute of Graduate Studies in Science
2017
00
Master'sOpen AccessTR

Ağır iyon çarpışmalarında lepton çiftlerinin üretilme olasılıkları

Ağır iyonların rölativistik hızlarda çevresel çarpışması birçok fiziksel olayın keşfedilmesine katkı sunduğundan dolayı, günümüze kadar birçok çalışma yapılmıştır. Rölativistik hızlarda hareket eden çekirdekler hareket yönünde Lorentz boyca kısalmasına uğrarlar ve uç noktalarda kuvvetli elektromanyetik alanlar oluşur. Bu alanlar çok sayıda sanal foton içerir. Bu alanlar vektör bozonları, zayıf bozonlar ve Higgs bozonları gibi çok sayıda parçacık üretir. Bu tezde ağır iyonlar rölativistik hızlarda çarpışırken elektromanyetik alanlardaki sanal fotonların etkileşmesinin sonucunda üretilen elektron, müon, tau çiftleri üzerinde durulacak. Tamamen iyonize olmuş ağır iyonlar LHC ve RHIC de kütle merkezi sisteminde nükleon başına sırasıyla 100 GeV ve 3400 GeV enerjilerinde çarpıştırılmaktadır. Bu tezde 3400 ve 100 GeV enerjileri için altın iyonlarının çevresel çarpışması incelene-cek ve bu çarpışmadan dolayı üretilen leptonların diferansiyel tesir kesitleri ve olası-lıkları incelenecek.

Erkan Kurban
İstanbul Technical University · Institute of Graduate Studies in Science
2017
00
Master'sOpen AccessEN

Polimetilmetakrilat/grafen nanoplatelet nanokompozitin fiziksel özellikleri

Poly (methyl methacrylate) (PMMA) is a clear, transparent thermoplastic material with good mechanical properties, high resistance to weathering and excellent heat resistance. Mechanical, thermal, electrical and radiation shielding properties of PMMA can be improved by adding several nanomaterials with excellent properties. The enhanced PMMA materials are the ideal candidates for several application areas such as medical, sensor, solar cell, electronic and aerospace areas.In this study, Graphene Nanoplatelets (GNPs) was selected as nanofiller to enhance the mechanical, thermal, electrical and radiation shielding properties of PMMA. PMMA was produced via ATRP technique. GNPs nanofiller was dispersed by in situ polymerization method because it was the most efficient method to disperse the layered GNPs nanomaterial. SEM, XRD, FTIR, TGA, hardness and compression test, ultrasonic test and gamma transmission techniques are performed to examine the changes in the characteristic properties of PMMA. SEM characterization combined with elemental mapping technique showed that GNPs nanofiller homogeneously dispersed in the PMMA polymer matrix via in situ polymerization method. Besides, the results of the ultrasound tests were supported a homogeneous structure of PMMA/GNPs nanocomposites. XRD pattern of PMMA/GNPs nanocomposites presented a pick at ~26.5° , which is corresponding to the stacking of the graphene layers at a distance of 0.34 nm. The intensity of the pick increased with the rise of the GNPs concentration. The FITR spectra of PMMA/ nanocomposite presented similar spectra with pure PMMA, indicating that interaction occurred between GNPs nanofiller and PMMA polymer matrix. TGA results showed that with the addition of 2% GNPs, the 5% weight loss temperatures shifted from 196.73°C to 243.00°C, improved by 46.27 °C. The thermal stability of PMMA enhanced significantly. With the addition of 2% GNPs the electric conductivity of PMMA improved dramatically from ~ 10-14 S/m to 0.72 S/m. In the ultrasonic test, the Shear modulus, Young's modulus and Microhardness values of pure PMMA were increased by 19.5%,16.8 %, and 14.2% respectively with the addition of 2 wt.% GNPs. Compare to the pure PMMA, with the addition of 2 wt.% GNPs the Rockwell hardness and compressive strength increased by 19.9% and 42.7% respectively. For Cs-137 and Co-60 radioisotopes, with the rise of GNPs concentration, the linear attenuation coefficients increased slightly, however, the mass attenuation coefficients decreased slowly.

Maıhemutı Maımaıtıtuersun
İstanbul Technical University · Institute of Graduate Studies in Science
2017
00
Master'sOpen AccessTR

Biyolojik moleküllerin arsenik fosforen tek katmanlı hegzagonal yüzey üzerine adsorpsiyonunun incelenmesi

Nanoteknolojinin en önemli alanlarından birisi de iki boyutlu malzemelerdir. Grafenin keşfi ve yığın halinden nano boyuta geçerken göstermiş olduğu eşsiz optik, mekanik, elektronik ve manyetik özelliklerinin anlaşılması geleceğe dair umutları artırmıştır. Özellikle Grafenin keşfiyle ortay çıkan iki boyutlu malzeme sınıfının organik moleküller ile kombinasyonu sayesinde bu malzemelerin özelliklerinin ayarlanabilir olması biyomedikal alandaki kullanımını öne çıkarmaktadır. Mavi arsenik fosforen iki boyutlu aile sınıfında bulunan ve potansiyel uygulamaları konusunda teorik çalışmaları süren bir malzemedir. Bu çalışmada mavi arsenik fosforenin Glisin ve Serin organik molekülleri ile olan etkileşimini anlayabilmek için Yoğunluk Fonksiyonel Teorisi (YFT) kullanılmıştır. Çalışmanın ilk kısmında alttaş olarak kullanılan mavi arsenik fosforenin yapısal ve elektronik özellikleri ortaya konmuştur. İkinci kısımda ise yüzeyde kusurlar oluşturularak yapısal ve elektronik özelliklerin değişimi belirlenmiştir. Son bölümde de kusursuz ve kusurlu yüzeylerin biyomoleküller ile olan etkileşimi için yapısal optimizasyonları gerçekleştirilmiştir. Yüzeyin biyoalgılama kabiliyetini belirleyebilmek için yapısal ve elektronik özellikleri analiz edilmiştir. Tüm bu incelemeler sonucunda kusurlu mavi arsenik fosforen yüzeylerinin Glisin ve Serin etkileşimi için iyi bir aday olduğu görülmüştür.

AdsorpsiyonBiyolojik moleküllerElektronik özellikler+2
Okay Tercan
Ankara University · Institute of Graduate Studies in Science
2023
00
DoctorateOpen AccessTR

Yeniden tam güçlendirme yöntemi ile doğal gaz kombine çevrim santraline dönüştürülen bir termik santralin modellenmesi ve performans değerlendirmesi

Endüstriyel gelişmenin bir sonucu olarak sürekli artan elektrik talebi, daha büyük kurulu güç ve üretim kapasitesine duyulan ihtiyacı da beraberinde getirmektedir. Bununla birlikte, mevcut yasal düzenlemeler, yeni ekipmanların sermaye maliyetleri, zamana bağlı kısıtlamalar ve enerji santrallerinin inşa edilmesine karşı toplumsal tepkiler, yeni enerji üretim projeleri için zorluklar oluşturmaktadır. Bu zorlayıcı faktörler son yıllarda "yeniden tam güçlendirme" kavramının tekrar önem kazanmasına neden olmuştur. "Ambarlı Yeniden Güçlendirme Projesi" Türkiye'de ilk defa yürütülen, dünyada ise boyutu, kapsamı ve niteliği açısından sınırlı sayıda örneği olan bir "Doğal Gaz Kombine Çevrim Santraline Dönüştürerek Yeniden Tam Güçlendirme" projesidir. Söz konusu projede mevcut fuel-oil yakıtlı buhar santrali, doğal gaz yakıtlı kombine çevrim santraline dönüştürülerek yeniden tam güçlendirilmiştir. Bu tez kapsamında, mevcut buhar türbininin ilk performans hesaplamaları ve rehabilitasyon sonrası elde edilebilir güç çıkışı detaylı olarak değerlendirilmiştir. Türbin giriş sıcaklığı, basınç ve buhar debisi gibi parametreler, kombine çevrim santralin performansının kapsamlı bir şekilde değerlendirilmesine olanak tanıyan simülasyon modeli için sınır koşulları olarak tanımlanmıştır. Geliştirilen modelin çıktılarının resmi performans test sonuçları ile karşılaştırılarak doğrulanması amacıyla detaylı bir validasyon çalışması yürütülmüştür. Sonuçlar, kondenserden ısı deşarjında sadece %25 bir artış ile santralin toplam kapasitesinin %203 oranında artırılabileceğini göstermektedir. Ayrıca yeniden güçlendirmenin, ekonomik faydalara ek olarak, NOx, SOx ve CO2 emisyonlarının azaltılması gibi önemli olumlu çevresel etkilere sahip olduğu da bulunmuştur. Resmi performans testleri ile doğrulanan bu özgün çalışmanın, gelecekte yapılacak benzer projelere ışık tutması beklenmektedir.

Atık ısıBuhar türbiniGaz türbini+3
Anıl Kurbanoğlu
Ankara University · Institute of Graduate Studies in Science
2023
00
DoctorateOpen AccessTR

Kuantum mekaniğinin matematiksel ve kavramsal temelleri üzerine

Kuantum mekaniğinin matematiksel ve kavramsal temelleri, çeşitli Mach-Zender tipi hibrit deney düzeneklerinde, girişimölçerlerin iki ayrı kolu tarafından saçılan dolanık durumdaki bir çift parçacığın spin ölçümleriyle ilişkili korelasyon bağıntıları üzerinden incelenmiştir. Kuantum durumlarının uyumu, oluşum dolanıklığı, kuantum öze uygunluk ve Bures mesafesi, geometrik fazın dolanık parçacık çiftlerinin ilk durumlarını nasıl etkilediğini anlamak için kullanılmıştır. Elektromanyetik potansiyeller, elektromanyetik alanların bulunmadığı bölgelerde parçacıkların hareketinden dolayı bir kuantum girişimine neden olmaktadır. Bazı durumlarda, geometrik faz bilgisinin dolanık parçacık çiftlerinin son durumlarında mündemiç olduğu gösterilmiştir.

Geometrik faz
Melik Emirhan Tunalıoğlu
Ankara University · Institute of Graduate Studies in Science
2023
00
Master'sOpen AccessTR

Mamografi çekimi yapılan hastalarda cranio caudal çekim protokolüne göre konvansiyonel ve dijital mamografide yüzey dozunun karşılaştırılması

Dijital mamografi cihazında 230 ve konvansiyonel mamografi cihazında 180 hastada meme üst ve iç yüzeyinden çekim alınmıştır. Konvansiyonel mamografide 50 hastadaki çekimde bunlara ilaveten meme dış ve alt yüzeyinden çekimleri eklenerek dört farklı noktadan ölçüm alınmıştır. Bunun için TLD-100 dozimetre kullanılarak dozimetrik yöntemle ölçümler yapılmıştır. Toplam 460 hastada elde edilen sonuçlar karşılaştırıldığında dijital mamografi ile yapılan çekimlerde konvansiyonel mamografiye göre meme üst ve iç yüzeyinden alınan dozların bu çalışmada daha fazla olduğu belirlenmiştir. Çalışmada aynı zamanda meme ultrasonu sırasında tespit edilen meme dansitesi değerleri, hastanın meme ölçüleri, ölçüm sırasında kullanılan kVp, mAs değerleri de çalışmaya eklenmiştir. Anahtar Kelimeler: Konvansiyonel Mamografi, Dijital Mamografi, yüzey dozu, TLD- 100 dozimetre

Doz-cevap ilişkisi-radyasyonMamografiMeme+5
Yasemin Kavas
Ankara Yıldırım Beyazıt University · Institute of Health Sciences
2016
00
Master'sOpen AccessEN

Noise mapping on Gaziantep University campus area

Noise is an element that needs to be taken seriously, such as all other environmental pollution, and to be controlled. There are many sources that generate noise both internally and externally. If the noise is not controlled, we will encounter in every area of our daily life and become a factor which will cause constant discomfort. This brings a lot of health problems in a long or short time, constant or instant. Noise pollution is one of important parameters for irregular urbanization. The aim is researching about the noise pollution in Gaziantep University Campus, which is caused by vehicle traffic on highway, and taking precautions. In this study, eight points of Gaziantep University Campus were examined in terms of environmental noise. Based on the vehicle loads on these points, noise map was prepared by using Grid Noise Map technique.

Muhammet Hudayfa Atasoy
Gaziantep University · Institute of Graduate Studies in Science
2021
00
DoctorateOpen AccessEN

Conversion of radioactive and chemical energy to electrical energy

In this thesis, two types of batteries have been studied. The first is aluminum (Al) air battery and the other is nuclear battery. We have demonstrated that graphite and exfoliated graphite sheets coated with activated carbon (AC), manganese dioxide (MnO2) and other additives are a promising cathode for metal air batteries. Several low-cost, environmentally-friendly air cathodes are fabricated and their performances are tested by constructing Al air batteries whose electrolyte 6M NaOH, including ZnO inhibitor, is gelled by adding a cost-effective water retainer. The experimental results show that this new Al air battery has a good discharge performance. In the other study, we present construction and analysis of nuclear micro battery driven by Strontium 90 (Sr90). Our design is based on charge deposition on the plates of a capacitor and polarization of dielectric materials between the plates. In the construction, we have used liquid Sr90 with activity 100 mCi in cylindrical ampoule coiled up by thin film graphene as one plate and Manganese dioxide (MnO2) as other plate of the capacitor. The high energetic beta particles from the Sr90 penetrate to graphene to produce ionization and then electrons are removed from graphene to dielectric material. Electrons inside the dielectric material cause polarization of dipoles. Consequently, the radiation from the isotope produces an external current.

Seda Özkeçeci
Gaziantep University · Institute of Graduate Studies in Science
2021
00
Master'sOpen AccessEN

Improvement of signal significance of Ds± meson's signalvia using artificial neural network

The aim of the analysis is to improve the significance of the Ds ± meson signal in ALEPH data which is recorded at LEP in the Ds± → π± + φ where φ mesons are reconstructed from φ →K+ K- decay channel. The analysis covers two phases. In first phase, reconstruction of particles in the decay channel is performed and input variables are stored to be used in classification. This phase is the machine learning part of the analysis. The second phase is the selection of an optimum algorithm for classification of signal and background. Improvement of significance of Ds meson's signal is performed after selection of the optimum algorithm and the evaluation of coefficients for relevant input variables which are stored in first phase. Classification is performed with the Toolkit for Multivariate Analysis (TMVA) which operates under the ROOT data analysis framework. TMVA includes many classification algorithms; the Boosted Decision Tree method is chosen as the optimum classification method.

Particle physicParticle accelerationSoftware
Mustafa Koşmaz
Gaziantep University · Institute of Graduate Studies in Science
2021
00
DoctorateOpen AccessEN

The growth and characterization of Sn doped Al/ZnS/p-Si structures

In this study, undoped and Sn (tin) doped ZnS (zinc sulfide) solutions were coated on glass and p-type Si (silicon) crystal using the sol-gel method. The Sn contribution amount changed between 0%-10%. The films are coated 15 layers on glass and 6 layers on crystal. Optical parameters such as thickness d, forbidden band gap Eg and refractive index n of the materials were investigated by using UV-vis-NIR measurements of thin films coated on glass. The crystal structure of the materials was determined with help of XRD spectrum. According to the results obtained, it was observed that the films grown on both glass and crystal crystallize as a cubic structure. Current-voltage I-V measurements of doped and undoped ZnS/p-Si structures were taken at room temperature in the dark, and diode properties of the samples were investigated with the help of these measurements. Diode parameters such as ideality factor n, barrier height ϕb and series resistance Rs were calculated using Thermionic emission (TE), Norde, Lien and Cheung-Cheung methods. In addition, capacitance-voltage C-V measurements of doped and undoped ZnS/p-Si in the frequency range of 10kHz-1.5MHz were taken and diode parameters were determined in detail by using these measurements. In addition, illuminated I-V measurements of doped and undoped ZnS/p-Si structures were determined under 100mW/cm2 illumination power in order to investigate photodiode characteristics of the samples.

DiodesSol-gel methodZinc sulfate+1
Şirin Uzun Çam
Gaziantep University · Institute of Graduate Studies in Science
2022
00
DoctorateOpen AccessEN

Examination of the performance of anechoic chambers and reverberation rooms at low frequencies

Determination of sound power level of the noise source is based on sound pressure and sound intensity measurements. ISO 3740 series standards are used in that purpose. Measurements are performed in anechoic chamber or hemi-anechoic chamber satisfying the free field condition and reverberation room obeying the free diffusivity condition. The lower frequency (cut-off frequency) for the measurement is directly related to the physical structure of the rooms. The inverse square law is examined in determining the cut-off frequency for anechoic and hemi-anechoic chambers. For reverberation rooms, on the other hand, diffusivity control that is the adjacent band value difference, standard deviation and reverberation time measurements are performed. Sound pressure level measurements of a sound source can be performed in a verified anechoic, hemi-anechoic and a reverberation rooms. In addition, absorption coefficient measurements can also be performed in the reverberation rooms. The aim of this thesis is to examine the performances of TUBITAK UME anechoic chamber built according to ISO 3745 standard and TUB¨ ˙ITAK UME reverberation room built according to ISO 3741 standard below their cut-off frequencies. Concurrently, the other aim of thesis is to compare the measurement surfaces describes in ISO 3744 and ISO 3746 standards for the anechoic chamber based on the sound power level, the level of uncertainty contribution due to the measurement surface, the level of uncertainty contribution due to the number of microphones and directivity indices.

NoiseCut-off frequencySound pressure+2
Haydar Mutaf
Gaziantep University · Institute of Graduate Studies in Science
2022
00
DoctorateOpen AccessEN

CERN-ATLAS deneyinde S= 13 TeV kütle merkezi enerjisi verisiyle B+ mezon üretim tesir kesitinin ölçülmesi

The differential cross section of B+ meson is presented as a function of transverse momentum and pseudorapidity. It is determined from the channel B+ ->J/psi K+ and reconstructed with using ATLAS pp collision dataset, Run2 2015 data with integrated luminosity of 3.2 fb-1. Measurement is done for 8 intervals of transverse momentum pT and 4 intervals of rapidity |y| covering the range 9 GeV < pT< 120 GeV and |y|< 2.25. B+ / B- ratio is consistent with MC and 13 TeV / 7 TeV cross-section ratio is consistent with the theoretical expectations.

Zekeriya Uysal
Gaziantep University · Institute of Graduate Studies in Science
2023
00
Master'sOpen AccessEN

A study on the mass attenuation coefficients of different tissues for human body using finite element method

The values and so the estimation of the total mass attenuation coefficient is an important parameter for the interaction of radiation with tissue and in dosimetry for the medical applications in radiology and in oncology. The full mass attenuation coefficient is identified by both photon energy in addition to constituent elements of the materials. Presently, the human phantoms and computer simulation is the main preferred methods to achieve this task. In this study a novel model design by Finite Element Method (FEM) interactive environment in order to simulate and calculate the mass attenuation coefficients of gamma ray for several human organs. These organs include tissue, adipose tissue, blood, brain, bone, muscle, lung, skin and eye lens. Commonly used Gamma ray with several energies has been tested and these energy ranges are;60KeV, 80KeV, 150KeV, 400KeV, 500KeV, 600KeV, 1000KeV, 1250KeV, 1500KeV, and 2000KeV. The results have been compared with theoretical methods XCOM program and simulation program-based Monte Carlo model which are GEANT4 and FLUKA program as well as NIST. The proposed model results are very close to XCOM results and are very close to NIST values. These results are more accurate than FLUKA and GEANT4 simulation packages. Therefore, this method can be considered as a new method with high accuracy in the calculation of the mass attenuation coefficients of human tissues that can be relied upon with reliability.

Alı Husseın Mohammed Alı
Gaziantep University · Institute of Graduate Studies in Science
2023
00
Master'sOpen AccessEN

Acoustical analysis and evaluation of some culture and art centers in Gaziantep

In recent years, room acoustics, one of the subcomponents of acoustics, has received great attention among researchers for its ability to specify good hearing conditions for each audience and to ensure high speech intelligibility and clear perception of music and its components in cultural or art centers and auditoriums. Therefore, acoustical conditions should be taken into account to prevent corresponding acoustical defects. The main objective of this thesis is to perform a general evaluation of the acoustical performance of some selected major culture and art centers in Gaziantep using objective parameters such as RT, EDT, BR, TR, Ts, C80, D50, STI, and Background Noise values. The selected centers are the Şehitkamil Culture Center, Şehitkamil Art Center, and Şehitkamil Wedding Hall. The objective acoustical performance of the audience area in culture and art centers depends on the measured parameter obtained by sound level meter or computer programs. The selected culture and art centers will be simulated and analyzed using the ODEON room acoustics software.

Architectural acoustic
Mehmet Uncu
Gaziantep University · Institute of Graduate Studies in Science
2023
00
Master'sOpen AccessEN

An invariant mass method for the energy calibration ofneutral pions

Data collected in the 1990's from the ALEPH experiment at the LEP collider still has potential to provide new or improved precision measurements in particle physics. In the ALEPH data neutral pions suffer from poor calibration. In this study, an energy calibration based on a global mass constraint is applied to neutral pions in order to further improve the quality of ALEPH data. The calibration is obtained by modifying photon energies with a scale such that the mean reconstructed mass is equal to the nominal pion mass. Since the reconstructed mass of neutral pions is observed to run with energy, individual scales are determined for 50 energy intervals independently for both simulated and real data. The calibration is also performed independently for four π 0 topologies. We show that this procedure improves pion energy resolution and the agreement between simulated and real data. This calibration is expected to lead to improved statistical significance in measurements of particle production and help to reduce systematic errors in those analyses.

Roha Awıja
Gaziantep University · Institute of Graduate Studies in Science
2023
00
Master'sOpen AccessEN

Evaluation of outfield radiation dose in the treatment of breastcancer with hypo-fractionated radiation therapy usingthermoluminescence dosimetry

The aim of the study was to evaluate the outfield radiation dose in the treatment of breast cancer using hypofractionated radiation therapy with thermoluminescence dosimetry, specifically TLD-100 (LiF: Mg, Ti). To assess the variability in TLD responses, we employed the element correction factor (ECF) generation method. For measuring point doses in organs outside the treatment fields, we placed sixteen TLD- 100 chips in nine specific locations within the Rando phantom used for breast cancer radiation treatment (260 cGy x 16 = 41.6 Gy in 16 fractions). The TLDs were read using a Harshaw QS 3500 manual type reader connected to a PC, where we studied and analyzed the thermoluminescence signals. The results indicated that the highest received dose values were observed in the esophagus (≈3960 cGy) and trachea (≈3464 cGy). Furthermore, our findings demonstrate that TLD-100 chips are suitable for measuring point doses in hypofractionated radiotherapy for breast cancer.

Ömer Yegen
Gaziantep University · Institute of Graduate Studies in Science
2023
00
Master'sOpen AccessEN

Investigation of the effect of heating rate on the dose dependence of tl glow curves of Li2B4O7: Mn (TLD - 800)

In this study, the effect of the heating rate on the dose dependence of TL glow curves of Li2B4O7: Mn (TLD-800) have been investigated by using the supralinearity function, f(D). The dose response functions have been evaluated at different linear heating rates between 1 oC/s and 20 oC/s. The results of this study have showed that, the main peak shows high linear behaviour at linear heating rate of 3 oC/s and 4 oC/s. Also the peak temperatures of all peaks are shifted higher temperatures and the integrated peak area of the curves decreases by about 65 %. as the heating rate increases as expected in theory because of the thermal quenching effect.Keywords: Li2B4O7: Mn (TLD-800), f(D), thermal quenching.

Dlgash H. Al. Zeebaree
Gaziantep University · Institute of Graduate Studies in Science
2013
00
Master'sOpen AccessEN

Physical realization of controlled quantum gates

In this thesis, we briefly survey the quantum computers history and the main parts of each computer, also mention some quantum computation's rule. Then, several illustration of some quantum gates by solving the time-dependent Schrödinger equation for several desired Hamiltonians and by controlling the parameters of time-dependent probability equation. We have tried to show the physical realization of quantum gates theoretically. In addition the simulations of the systems and graphs is performed by using

İbrahim Nazem Qader Al-jaf
Gaziantep University · Institute of Graduate Studies in Science
2013
00
Master'sOpen AccessEN

Reconstruction of neutral pions from photon conversions

In this study, the low energetic photon conversion process in the ATLAS detector has been discussed. The conversion candidates selected from minimum bias events at √s=8 TeV are used to reconstruct π^0 particles built from two-photon invariant mass distribution. A clear π^0 peak is obtained and fitted to Gaussian function. The results reveal that purity of the π^0 signal depends strongly on the χ^2 value of the e^+ e^- pairs. It is also found that the optimal mass window cut for selecting π^0 candidates is around ±2σ around the π^0 peak.

Mehmet Arslan
Gaziantep University · Institute of Graduate Studies in Science
2014
00
Master'sOpen AccessEN

Investigation of the characteristics of the boron doped MnO films deposited by spray pyrolysis method

In this study, the influence of boric acid concentration on the structural and optical properties of sprayed MnO:B films were widely investigated by using different techniques. Boron-doping was achieved by adding 0.1M, 0.2M, 0.3M and 0.4M H3BO3 to the starting solution. The crystal structure of the undoped and boron doped films were determined from x-ray diffraction peaks. The diffraction pattern exhibit peaks at 2θ=28.4098°, 2θ=47.28580 and 2θ=56.0638° were identified to be (111), (220) and (311) planes having cubic structure with lattice parameter, approximetly, a=5.4Å. The band gap of the films were changed from 2.25 to 2.54 eV with boron concentration. The slight decreases in the optical band gap of the films with the increasing boron concentration. The surface morphology of the sprayed undoped and boron doped films were analysed by scanning electron microscopy (SEM).

Ali Tunç
Gaziantep University · Institute of Graduate Studies in Science
2015
00
DoctorateOpen AccessEN

Woods-saxon potansiyeli içeren bohr hamiltoniyeninin özel çözümleri

The recent influential studies on the nuclear structure have focused on the quantum shape phase transitions of atomic nuclei within the frame of the Collective Model, which have enabled many researchers to test the reliability of the models used. As the special solutions of the Bohr Hamiltonian dealing with collective behaviour of the nucleus in terms of collective variables beta and gama in five-dimension, E(5) and X(5) are the most important critical point symmetries, which describe the shape phase transition between vibrational and gama-unstable/axially symmetric prolate rotor, respectively. Hence, for the first time in the related literature, considering both E(5) and X(5) critical point symmetries, the Bohr Hamiltonian with the well-known Woods-Saxon potential involving the repulsive angular momentum barrier in the non-relativistic domain is solved analytically. We observe that the corresponding new solution well reproduces energy spacing within the ground state and gama bands for more than 100 even-even deformed nuclei, and gives an insight to the physically acceptable parameters that is required for reliable and accurate calculations.

Mustafa Çapak
Gaziantep University · Institute of Graduate Studies in Science
2015
00
Master'sOpen AccessEN

The investigation of natural radioactivities and hazard index for soil sampls around Pshdar region in Iraq

The main aim of this project is to evaluate the activity concentrations of naturally occurring materials associated with the 238U, 235U, 232Th decay chains and the long-lived natural occurring radionuclide 40K in environmental samples. The soil samples were collected from the Pshdar area was determined by means of a gamma-ray spectrometry system using a High pureity germanium (HpGe) detector in a low background configuration. It was found that the activity concentrations of 226Ra, 232Th and 40K were ranging from 7.6±1,0 Bq kg-1 to 23.5±1.7 Bq kg-1, 2.50 Bq/kg to 31.8±2.2 Bq kg-1 and 77.6±7.8 Bq kg-1 to 554.5±42.7 Bq kg-1, respectively. The value of the absorbed dose rate indoor, the absorbed dose rate outdoor, the annual effective dose, the radium equivalent activity, the external hazard index, the internal hazard index and the gamma index in the soil samples were also determined and found to have a range of 14.25 nGy h-1 to 85.23 nGyh-1, 7.33 nGyh-1to 45.08 nGy h-1, 0.07 mSv to 0.42 mSv, 15.71 Bq kg-1 to 96.12 Bq kg-1, 0.04 to 0.26, 0.07 to 0.32, 0.07 to 0.34, respectively. The results indicate that the radiation hazard from primordial radionuclides in all soil samples from the area studied in this current work is not significant.

Peshawa H. Ali Mangurı
Gaziantep University · Institute of Graduate Studies in Science
2015
00
Master'sOpen AccessEN

Solution of Klein-Gordon equation in D-dimension and its application in physical systems

The analytic and approximate solution of KG-equation in arbitrary dimension D are calculated by using Asymptotic Iteration Method. The system of some important type of potentials like harmonic oscillator potential, the Go'ldman-Krivchenkov potential and some exponential-type potentials such as Morse and Woods-Saxon potentials have been studied in the D-dimension. The corresponding eigenvalues are obtained. In addition, the total normalized eigenvectors are obtained after calculating normalization constant for each type of potentials. Furthermore, it is shown that application of Asymptotic Iteration Method in KG-equation gives the eigenvector solution in terms of the Gauss hypergeometric or its special cases using the wavefunction generator.

Aram Bahroz Brzo
Gaziantep University · Institute of Graduate Studies in Science
2016
00
DoctorateOpen AccessEN

Computational modelling of highly mis-matched alloys of GaNAsP and GaNAsBi as a laser gain material

The aim of this thesis work is to model and investigate the electronic band structure and current density of highly mismatched alloys of GaNAsP and GaNAsBi. To reveal the importance of these highly mismatched alloys we provide a comparison of GaNAsP and GaNAsBi with their nitrogen free N-counterpart. The GaP-based dilute nitride direct bandgap material Ga(NAsP) is gaining importance for the monolithic integration of laser diodes on Si microprocessors. The major advantage of this newly proposed novel laser material system is the small lattice mismatch between GaP and Si. However, from first gain measurements it is found that Ga(NAsP)/GaP material system has high threshold current at room temperature. Therefore, we present a comprehensive theoretical analysis of band alignment and threshold current in dilute nitride direct bandgap Ga(NAsP)/GaP/AlGaP QWs on silicon substrates using model calculations. The comparison of our calculated results with that of the experimental data indicates that the Auger effect involving CHCC process can be considered as the dominant non-radiative loss mechanism at 300K. It has just recently reported that highly mismatched semiconductor alloys of GaAs(1-x)Bi(x) has also several novel electronic properties, including a rapid reduction in energy gap with increasing x and also a strong increase in spin-orbit-splitting energy with increasing Bi composition. We, therefore to understand the origins of the rapid reduction in energy gap and its consequences, study and compare band gap and critical thickness of GaNAsBi. The results indicate that GaNAsBi material can be used in optoelectronic applications in the long wavelength region.

Solid state lasersLayered semiconductors
Ömer Lütfi Ünsal
Gaziantep University · Institute of Graduate Studies in Science
2016
00
Master'sOpen AccessEN

Gaziantep şehrinin Şahinbey, Nurdağı ve İslahiye ilçelerinin topraklarında doğal radyoaktif seviyelerinin belirlenmesi

The aim of this thesis is determine of the level of natural radioactivity in 61 soil samples taken from different regions of Islahiye, Nurdagı and Sahinbey districts of Gaziantep city. 238U, 232Th and 40K radioactivity concentrations of radionuclides in soil samples taken from these district were measured by using a well type NaI(TI) detectors connected to multichannel analyzer (MCA). The results of the natural radioactivity of the region that have been evaluated according to specific criteria. Average specific activities of 238U, 232Th and 40K in soil samples taken from İslahiye, Nurdağı and Şahinbey districts in Gaziantep city were found to be 39.18 ± 21.52 Bq/kg, 44.30±20.81 Bq/kg and 325.54±42.13 Bq/kg, respectively. The average 40K activity values were found to be slightly lower than international average effective value given by UNESCEAR 2000 report. Key words: İslahiye, Nurdağı, Şahinbey, Gamma Spectroscopy, NaI(TI) detector.

Mehmet Kılınç
Gaziantep University · Institute of Graduate Studies in Science
2016
00
Master'sOpen AccessEN

The investigation of variation of TL dose response curve of natural calcite after annealing at different temperatures

The thermoluminescence (TL) studies of calcite mineral have resulted in the development of a wider range of applications in ceramic industry field. The TL glow curve shapes of minerals changes as a result of crystal purity, radiation dose, and thermal history previous the irradiation. In this study, the TL dose response of natural calcite samples of unannealed and annealed at different temperatures has been studied. The calcite samples that were collected from Elazığ-Ağın city in Turkey exhibit two main TL peaks following β-irradiation. The samples were annealed at 600, 700, 800, 900, 1000 oC from 15 minutes to 240 minutes and then they were irradiated at room temperature with a point beta source for different time durations to study TL dose response curve. It was observed that the annealings at 900 and 1000oC have high prononuced effects on the dose response curve of natural calcite.

Cengiz Bozada
Gaziantep University · Institute of Graduate Studies in Science
2017
00